User manual MICROTEK GNC M C893 XXXX

[. . . ] · Consult the dealer or an experienced radio/TV technician for help. Caution: To comply with the limits for an FCC Class B computing device, always use the shielded signal cord supplied with this unit. The Federal Communications Commissi on warns that changes or modifications of the unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. CE mark for Class B ITE (Following European standard EN55022/1998; EN61000-3-2/1995; EN61000-3-3/1995, EN55024/1998, EN60950/1992+A1+A2+A3+A4+A11) Radio Frequency Interference Statement Warning: This is a Class B product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures. Canadian Doc Notice For Class B Computing Devices This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulation of the Canadian Department of Communications. "Le présent appareil numérique n'èmet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class B prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada" 2 18" LCD monitor Important Safety Instructions Please read the following instructions carefully. [. . . ] In case of loss, contact the retailer or service center. If you lose the power cord, you must purchase a power cord of the same type and configuration. l Japan : VCTF type, 3 wires or with ground-wire, T-mark approval is required. 3 18" LCD monitor l l U. S. : VW-1; 18AWG X 3C; SVT with national approval as UL and/or CSA approval/number(s) Europe : VDE / Ö VE and/or KEMA approval; H05VV-F, 3G, 0. 75mm , or equivalent. 2 The power cord should bear the name of the manufacturer and state the type of cord that it is. 4 18" LCD monitor CHAPTER 1 INTRODUCTION BEFORE INSTALLING YOUR MONITOR Read this manual carefully. PAY ATTENTION to all Warning and Caution messages. DO NOT use computer components not recommend by the manufacturer. Do not attempt to service the monitor yourself. If a problem occurs, contact the manufacturer's authorized service center. ABOUT YOUR MONITOR This monitor is a microprocessor-controlled, color monitor that uses a TFT LCD panel. The monitor conforms to EPA Energy Star and VESA DPMS (Display Power Management Signaling) power management standards. RGB MODE This monitor is equipped with a microprocessor that identifies your computer 's video mode and allows you to adjust the setting. 5 18" LCD monitor FACTORY-PRESET MODES Table 1 shows standard video mode settings that have been pre-adjusted at the factory for accurate video display. These setting are stored in the monitor's memory. Factory-Preset Modes Mode NEC VGA Resolution 640x400 640x350 720x400 640x480 640x480 640x480 800x600 800x600 800x600 800x600 1024x768 1024x768 1024x768 1280x1024 1280x1024 640x480 832x624 1024x768 1024x768 H-Freq. (KHz) 24. 83 31. 47 31. 47 31. 47 37. 86 37. 5 35. 16 37. 88 48. 08 46. 87 48. 36 56. 47 60 63. 98 80 35 49. 7 48. 78 60. 241 V-Freq(Hz) 56. 4 70 70 60 72 75 56. 3 60. 3 72. 2 75 60 70 75 60 75 66. 7 74. 55 60 74. 927 SVGA XGA SXGA Macintosh 6 18" LCD monitor SPECIFICATIONS l 18" LCD Monitor Overall Dimension (HxWxD): Shipping Weight (G/W): Effective Display area (H/V): Display colors: Scan Frequencies: Horizontal Vertical Viewing Angle Contrast Ratio Response time ( Tr + Tf ) Native Resolution Pixel pitch: Power: Input Consumption Video Connector: RGB Signals: Video Sync Display Data Channel: Compatibility 426 x 444 x 215 mm 11Kg 359. 04 x 287. 23 mm 16. 7M colors 31. 47KHz to 80KHz 60Hz to 75Hz 160 /160 degree H/V 400:1 30ms 1280x1024(SXGA) 0. 279x0. 279 mm 110-240VAC (auto-sensing) Frequency: 48-62Hz 48 Watts maximum (ON) 1 Watt (Power-saving OFF mode) 15-pin Mini D-sub (Standard) Analog RGB 0. 7Vp-p/75 Separate VESA DDC 1/2B 7 18" LCD monitor Control Type: Compatibility: Environmental Limits: Operating Temp. Operating Humidity Storage Humidity Agency Approval EMI Energy Saving Safety Digital IBM and compatibles, Apple Macintosh, NEC 32°F to 113°F ( 0°C to 45°C ) -4°F to 140°F ( -20°C to 60°C ) 10% to 85% without condensation 10% to 95% without condensation FCC-B EPA energy star UL 8 18" LCD monitor CHAPTER 2 INSTALLING THE MONIT OR The monitor is equipped with an auto sensing power supply for voltage ranges from 110~240VAC, 60/50Hz. Confirm the line voltage designation on the rear panel of the monitor. FOLLOW THESE STEPS T O INSTALL THE MONITOR 1. Before you connect the cables, make sure that the monitor and the computers are both turned off. Plug one end of the 15-pin signal cable to the monitor and the other end to the video signal connector at the rear of the system. Tighten the two screws on the cable connector on both ends. Otherwise the screen will be abnormal and the LED light will be yellow instead of the normal green color. Connect the power to the monitor through the AC/DC adapter. Connect the power cord to the AC outlet. 4. 9 18" LCD monitor 10 18" LCD monitor CONTROL FUNCTIONS The Monitor control functions are located on the lower right side of the front part of the monitor, just below the glass. The control functions are shown in the figure below and described in the following paragraphs. The control key description: 1. Sel : Power Switch : Decrease / increase : Cursor Down function 5. [. . . ] If there is still no display, press the other Adjustment Control button several times. If step 2 doesn't work, connect your PC system to another external CRT. If your PC System functions properly with a CRT Monitor but it does not function with the LCD Monitor, and the LCD Monitor's power LED is blinking, the output timing of the PC's VGA card may be out of the LCD's synchronous range. Please change to an alternate mode listed in table 1 on page 2 or replace the VGA card and repeat steps 1 and 2. [. . . ]