User manual MIDAS CONSOLES DL371 AUDIO SYSTEM ENGINE ISSUE C

[. . . ] DL371 Audio System Engine Operator Manual Midas Klark Teknik Limited, Klark Industrial Park, Walter Nash Road, Kidderminster. Tel: +44 1562 741515 Fax: +44 1562 745371 Email: info@midasklarkteknik. com Website: www. midasconsoles. com DL371 Audio System Engine -- Operator Manual DOC02-DL371 Issue C -- July 2010 © Red Chip Company Ltd. In line with the company's policy of continual improvement, specifications and function may be subject to change without notice. This Operator Manual was correct at the time of writing. [. . . ] Carefully pull out the module by its top and bottom eject handles. DL371 Audio System Engine Operator Manual 20 >> To fit a module 1 2 Make sure that the unit is switched off and electrically isolated (see "To remove power from (electrically isolate) the unit" on page 16). At the rear of the unit, offer up the rear of the module to its required module position. Make sure that the module is in the correct orientation and that the bottom eject handle is in the angled down position, as shown in the following diagram. Rear of DL371 Audio Cut-out Bottom eject handle to be in the angled down position Module 3 Insert the module into the empty slot and push it carefully, but firmly, into position. The bottom eject handle will clip back up into its fully fitted position (matching the top eject handle) when the module is in place. Secure the module using the two securing screws (see Figure 1 on page 19). Connect up the unit and switch it on (see Chapter 4 "Getting Started"). Check that the new module is functioning correctly (see "DSP modules" on page 11). 4 5 6 DL371 Audio System Engine Operator Manual 35 Appendix E: Service Information This appendix provides instructions on routine servicing and cleaning, and gives details on equipment disposal. Routine maintenance To help keep your DL371 Audio System Engine unit in good working order and to make sure it gives you optimum performance, we recommend that you carry out the following: Monthly · · · Clean the unit, as detailed in "Cleaning the unit" on page 35. You can quickly carry out a visual check by switching the unit off and then on again, as they are all activated during power-up. Check functionality of equipment. Yearly · Clean the internal fans, see "Cleaning the internal fans" on page 21. Cleaning Switch off the unit and electrically isolate it from the mains before cleaning; see "To remove power from (electrically isolate) the unit" on page 16. Cleaning the unit Clean the unit using a dry, lint-free cloth. When cleaning the unit, take great care not to damage the pushbuttons. Cleaning the internal fans The unit's internal fans need to cleaned regularly to remove the build of dust, dirt etc. We recommend that they are cleaned at least once a year, provided the unit has been operated under normal conditions. However, if the operating conditions are more adverse or extreme, for example, if the unit is operated in the vicinity of smoke machines, new carpets etc. , this frequency should be increased accordingly. This procedure must be carried out by a fully qualified service engineer. If you have any queries, contact Midas; details can be found at the front of this manual. Voltage rail failure When the unit is powered, all three voltage rails must be live. Their status is monitored by the three LEDs in the psu section of the front panel (see "psu panel" on page 6), which should all be illuminated. If any one of the LEDs is extinguished, it is probably an indication of a serious problem and you should contact Midas Technical Support. DL371 Audio System Engine Operator Manual 36 Appendix E: Service Information Hot unplugging/plugging a PSU module Caution: While it is possible to replace a PSU module with power connected to the other two, this may cause a momentary interruption or noise on the audio outputs of the unit. Always mute any loudspeaker system before performing this procedure. If you have to replace a PSU module, it can be done with the DL371 Audio System Engine unit switched on. This is known as "hot unplugging" (removing) and "hot plugging" (fitting), and will enable you to change it quickly and save you having to disconnect the cables from the unit. >> To hot unplug/plug a PSU module 1 2 3 4 5 6 7 8 9 Mute all outputs (see Caution above). Switch off the power at the mains power outlet of the PSU you want to remove. Remove the mains IEC connector from the PSU module. [. . . ] >> To power down the PRO6 system Important Note: BEFORE switching off any of the PRO6 system components, don't forget to mute the audio from the speakers and switch off the speaker sub-system. 1 2 3 4 Mute the audio from the speakers and switch off the speaker sub-system. Switch off the DL371 Audio System Engine unit. Switch off the PRO6 Control Centre (see "To switch off the PRO6 Control Centre" on page 52). DL371 Audio System Engine Operator Manual 52 Appendix G: Setting Up A PRO6 System Switching the PRO6 Control Centre on/off Carry out the following to switch the PRO6 Control Centre on or off in a safe manner, observing all WARNINGS and Cautions. >> To switch on the PRO6 Control Centre Caution (1)! [. . . ]