User manual MIDLAND 74-200

[. . . ] Model 74-200 Digital Weather Receiver with NWR-SAME decoding and Digital clock with alarm PRODUCT INFORMATION The 74-200 N. W. R. / S. A. M. E. (National Weather Radio/Specific Area Message Encoding) Weather / All Hazard Monitor provides you with constant monitoring of your local National Weather Service broadcast for messages warning you of hazardous conditions. The NWR/SAME decoding allows you to hear only messages concerning the area concerning you. You now have a choice as to what information will be brought to you. [. . . ] Press and release the "Hour /Date" button to increment the Date by one day. Press and release the "Min / Month" button to increment the month by one month. MODE / Year" button to increment the Year by one year. Press the "Set" button to store your settings. MODE" button until "AL Time" is displayed in the upper left corner of the display. Press and release the "Hour / Date" button to change the Hour. Press and release the "Min /Month" button to change the Minute. Press the "Set" button to store your settings 3. To activate the alarm, set the switch on the right side of the 74-200 marked "ON OFF ALARM" to the ON position. The "SNOOZE" button on the top of the 74-200 is for advancing the alarm time by 9 minutes each time the alarm sounds. To switch OFF the alarm, move "ON/ OFF/ ALARM" switch to the "OFF" position. Adjusting the Weather Frequency We have not adjusted the weather frequency for your local area. Look up your city in the supplied Weather Service directory and note the freque ncy. Find the channel number that corresponds to your frequency. Open the top hatch to reveal the programming keys. Press and release the "PROGRAM" button then "YES" to display the current alert pattern. Press and release the "YES" button to keep that pattern or "NO" to change it to the other option then press and release the "YES" button to accept that option and continue with programming or press and release the "PROGRAM" button to return the radio to alert mode. NOTE: Remember if there are no buttons pressed for 30 seconds the 74-200 will go back to alert mode. To continue after the 74200 goes back to alert mode, go back to "Adjusting Weather Frequency" to continue with programming. . FIPS Code programming: 14 NOTE: The 74-200 has enough memory to store 15 "FIPS" codes. The next display after VOICE/ALERT will display six numbers. These numbers will determine the areas or counties that your 74200 will be set to respond to SAME messages. [. . . ] For compliance information contact: Midland Radio Corporation 1120 Clay St. Kansas City, MO 64116 Tel: (816) 241-8500 25 SPECIFICATIONS Specifications are nominal and subject to change. GENERAL Frequency Range (162. 4O, 162. 425, 162. 45, 162. 475, 162. 50, 162. 525, 162. 55MHz) Number of WX Channels . . . . . . . . . . . . . . . . 7 Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-14 Volts DC Dimensions . . . . . 200MM W x 53MM H x 131MM D (7 7 /8 x 2 1 /8 x 5 1 /4 in. ) RECEIVER 20 dB Quieting Sensitivity. . . . . . . . . . . . . . . . . . . . 0. 5 uV FIPS Code Sensitivity @5kHz Dev. . . . . . . . . 0. 5uV Channel Selectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . ±25kHz, 60dB Speaker Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . 8 ohms Power Output @10%THD. . . . . . . . . . . . . . . . . . . . . . . . 500 mW max. [. . . ]