User manual MIELE DA 259-2

[. . . ] Operating and installation instructions Cooker Hoods DA 259-2, DA 259-2 U DA 259-2 EXT, DA 252-2, DA 252-2 U DA 252-2 EXT It is essential to read these operating instructions before installing or using the machine to avoid the risk of accidents or damage to the machine. GWOZ M. -Nr. 06 487 780 Contents Caring for the environment . 13 Reading the filter operating hours counter . 13 Altering the filter operating hours counter . [. . . ] The indicator lamp for the grease filter touch control and one of the ­ /+ touch control lamps will flash. ^ Use the On/Off touch control to switch the fan off. The ­ /+ touch control lamps show the time which has been set: 1st lamp from the left = 20 hours 2nd lamp from the left = 30 hours 3rd lamp from the left = 40 hours 4th lamp from the left = 50 hours ^ Use the ­ /+ touch controls to select the desired time. ^ Confirm the selection by pressing the grease filter touch control. If the procedure is not confirmed within 4 minutes of programming the steps, the cooker hood will automatically revert to the "old" data. 14 Cleaning and care Before any cleaning or maintenance work the cooker hood must be disconnected from the mains supply. Ensure that: - it is switched off at the wall socket and the plug has been withdrawn (do not pull on the cable, only on the plug), or ­ the fuse has been withdrawn from the fused spur connection unit, or - the mains fuse is withdrawn, or - the screw-out fuse is removed (in countries where this is applicable). pot scourers or sponges which have been previously used with abrasive cleaning agents. E-Cloth A microfibre "E-Cloth" is available from the Miele UK Spare Parts Department, Part number 98013530, which is suitable for cleaning surfaces such as stainless steel, glass, plastic and chrome without the use of chemicals. Stainless steel Housing Warning: The surfaces and controls are susceptible to scratches and abrasion. Please observe the following cleaning instructions: ^ All external surfaces can be cleaned using warm water with a little washing up liquid applied with a well wrung out soft sponge or cloth. Do not use too much water when cleaning the controls. Water could penetrate into the electronics and cause damage. Avoid: ­ cleaning agents containing soda, acids or chlorides, ­ abrasive cleaning agents e. g. powder cleaners or cream cleaners, Stainless steel surfaces can be cleaned using a proprietary non-abrasive cleaning agent designed specifically for use on stainless steel. To help prevent re-soiling, proprietary conditioning agents for stainless steel can also be used. Stainless steel coloured controls These controls are made of stainlees steel coloured lacquered plastic and may suffer discolouration or damage if soiling is left on them for too long. Remove any soiling straight away. Do not use stainless steel cleaning agents on these types of controls. If you are unsure about a particular product or need further advice please contact your nearest Miele Sales office. See back page for address. 15 Cleaning and care Grease filters Re-usable metal filters are fitted which remove solid particles (oil, dust, etc. ) from the kitchen vapours, preventing soiling of the cooker hood. The filters should be cleaned regularly (at least every 3-4 weeks) to avoid a build-up of fat, but always clean as soon as the grease filter touch control lamp comes on. An over saturated filter is a fire hazard. ^ To take out the grease filters press the locking clips in towards the middle of the filter. Holding carefully, lower and remove the filter. ^ Clean the filters ­ by hand: with a nylon brush in, warm water with a little washing up liquid. [. . . ] Ensure that these match the household mains supply. For U. K. : Connection should be made either by a double pole fused spur connection unit, or a fused plug and a suitable switched socket. The On-Off switch should be easily accessible after the appliance has been built in. When switched off there must be an all-pole contact gap of 3 mm in the switch (including switch, fuses and relays according to EN 60 335). [. . . ]