User manual MIELE DA 262 BUILT-IN HOOD OPERATING MANUAL

[. . . ] Operating instructions Cooker hoods DA 262 i DA 272 i DA 292 i In order to protect yourself and avoid damage to your machine, it is absolutely necessary to read the operating instructions prior to installation and operation. ]ö M. -Nr. 04 076 101 Description of the appliance Description of the appliance 1 2 3 DA 262 i 4 5 6 7 8 DA 272 i / DA 292 i 4 5 6 7 8 2 Description of the appliance Description of the appliance The cooker hood is suitable for . Air extraction: Air is drawn in through the grease filter f, cleaned and directed outside. Air recirculation: Air is drawn in through the grease filter f and then through the active charcoal filters for cleaning. [. . . ] Select a power setting strong enough to clear the air: 1 2 3 IS or push the deflector plate in. Setting 1-2 = for normal operation Setting 3-Intensive setting (IS) = for removing heavy cooking odors Switch on the cooktop illumination switch if required. 9 Cleaning and care Cleaning and care Before any cleaning or maintenance work, the extractor must be disconnected from the mains supply (switch off at the wall socket and remove plug or the fuse). Cleaning The cooker hood housing may be cleaned using hot water to which a little mild detergent has been added. Never use a cleaner which scours or contains chlorine, acids or soda. These would damage the surface of the cooker hood. Grease filters Re-usable metal grease filters are builtin which remove solid particles (oil, dust, etc. ) from the kitchen vapors, preventing soiling of the cooker hood. The grease filters can be cleaned in a dishwasher or by hand. The grease filters should be cleaned regularly to ensure a trouble free operation of the extractor fan, at least every 1 or 2 months, or when they are visibly saturated or no longer effective. An over-greasy filter can lead to danger or fire. To remove the grease filters push the filter holder retainers towards the middle. DA 272 i, DA 292 i only: Press the clips at the side in using a blunt instrument and remove the retainers. Pull the filter cassettes and link pieces out for cleaning. The other parts can be cleaned in the dishwasher. by hand: with a scrubbing brush in hot water with detergent. in a dishwasher: place the filters with the short side upright in the lower basket, ensuring the spray arm is not obstructed. Important The wires in the power supply cable are colored in accordance with the following code: Green = ground Black = live White = neutral WARNING THIS APPLIANCE MUST BE GROUNDED For USA only: The cooker hoods are supplied with a 5 ft power supply cable ready for connection to an a. c. , single phase, 120 V / 60 Hz supply. Connection should be made in the junction box. Important The wires in the power supply cord are colored in accordance with the following code: Green/yellow = ground Blue = neutral Brown = live As the colors of the wires in the power supply cord of this appliance may not correspond with the colored markings identifying the terminals in your junction box, proceed as follows: The wire which is colored green and yellow must be connected to the terminal junction box which is marked by the letter E, or by the earth symbol z or colored green or green and yellow. The wire which is colored blue must be connected to the terminal which is marked with the letter N or colored white. The wire which is marked brown must be connected to the terminal which is marked with the letter L or colored black. WARNING THIS APPLIANCE MUST BE GROUNDED 13 Technical data Technical data DA 262 i Total rated load Light Voltage Frequency Fuse rating Connection cable with plug Maximum air throughput: Air extraction 225 W 15 W 120 V 60 Hz 15 A 5 ft (1, 5 m) DA 272 i 223 W 13 W 120 V 60 Hz 15 A 5 ft (1, 5 m) DA 292 i 235 W 16 W 120 V 60 Hz 15 A 5 ft (1, 5 m) 90-325 CFM (150-550 m3/h) 50-240 CFM (80-350 m3/h) 90-325 CFM ( 150-550 m3/h) 50-240 CFM (80-350 m3/h) 90-325 CFM (150-550 m3/h) 50-240 CFM (80-350 m3/h) Air recirculation 14 Installation Installation For installing the cooker hood, a cabinet is required. The minimum cabinet width required for each model is given below: ­ DA 262 i = 600 mm (23 5/8") ­ DA 272 i = 700 mm (21 9/16") ­ DA 292 i = 900 mm (35 7/16") The exhaust connection must be made by a suitably qualified and competent person. The distance between the top of the cooktop and the bottom of the cooker hood should be at least: 45 cm (18") above electric cooktops 65cm (26") above gas cooktops. [. . . ] ­ The use of exhaust ducting with a diameter less than 125 mm (5") and flat ducting increases the noise level of the cooker hood. Tight bends reduce the air throughput of the cooker hood. ­ Only use smooth or flexible pipes made from non-flammable materials for exhaust connection. ­ Where ducting is horizontal, it must be laid to slope away at 1 cm per metre (1/8" per foot) , to ensure no condensation drains into the appliance. [. . . ]