User manual MIELE DA 270 DÉCOR ISLAND HOOD OPERATING MANUAL

[. . . ] Operating and Installation Instructions Ventilation System DA 270-4 To prevent accidents and appliance damage, read these instructions before installation or use. en - US, CA M. -Nr. 07 260 851 Contents IMPORTANT SAFETY INSTRUCTIONS. 24 Distance between cooktop and hood (S) . 31 2 IMPORTANT SAFETY INSTRUCTIONS READ AND SAVE THESE INSTRUCTIONS Keep these instructions in a safe place and pass them on to any future user. [. . . ] See "Cleaning and care / Grease Filter". After the grease filter has been cleaned and put back in place, the grease filter timer must be reset. Checking the grease filter timer To check the percentage of time already used: ^ Press the On/Off button to turn the fan on. ^ Press the grease filter button. ^ To do this, press the grease filter button for about 3 seconds while the fan is running. The number of flashing "­/+" indicators show the percentage of programmed hours that have been used. 1 indicator 2 indicators 3 indicators 4 indicators = 25 % = 50 % = 75 % = 100 % The indicator lights. This information will remain stored in memory in the event of a power failure. 14 Operation Reprogramming the grease filter timer The grease filter timer is preset to 30 hours. This time can be lengthened or shortened to 20, 30, 40 or 50 hours. ­ A time of 20 hours should be programmed in kitchens with frequent pan or deep frying. ­ A time of 20 hours should also be programmed if the kitchen is only used occasionally to prevent grease which has accumulated over a long period of time from hardening on the filter, making cleaning more difficult. The lit "­/+" indicator shows the programmed time: 1st indicator from the left 2nd indicator from the left 3rd indicator from the left 4th indicator from the left = = = = 20 hours 30 hours 40 hours 50 hours ^ Use the "­/+" button to select the desired time. ^ Store the selection by pressing the grease filter button. ^ Press the On/Off button to turn off the fan. If the procedure is not stored within 4 minutes of programming the hood will automatically default to the "old" data. ^ Press the Delayed Shut Down and grease filter button at the same time. The indicator for the grease filter timer and one of the "­/+" indicators will flash. 15 Cleaning and care , WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: Before cleaning or servicing the hood, disconnect it from the power supply, see "Important Safety Instructions". Avoid: ­ cleaning agents containing soda, acids or chlorides, ­ abrasive cleaning agents e. g. powder or cream cleansers, ­ abrasive sponges, e. g. pot scourers or sponges which have been previously used with abrasive cleaning agents. These will damage the surface. Cleaning the casing Never use abrasive cleaners, scouring pads, steel wool or caustic (oven) cleaners on the hood. ^ The exterior surfaces and controls can be cleaned with a mild solution of warm water and liquid dish soap applied with a soft sponge. Only use a slightly damp sponge when cleaning the controls. Water could penetrate into the electronics and cause damage. ^ Glass surfaces can be cleaned using glass cleaner. The following instructions for cleaning "Stainless steel" surfaces and "Stainless steel colored controls" should be followed in addition to the general "Cleaning the casing" instructions. Stainless steel Stainless steel surfaces can be cleaned using a non-abrasive stainless steel cleaner. To help prevent resoiling, a conditioner for stainless steel can also be used. [. . . ] Do not vent exhaust air into spaces within walls or ceilings or in attics, crawl spaces, or garages To reduce the risk of fire, only use metal ductwork. Please read and follow the "IMPORTANT SAFETY INSTRUCTIONS" to reduce the risk of personal injury. Follow all local building codes when installing the hood. Exhaust ducting and connections ­ The ducting should be as short and straight as possible, and the number of sharp bends should be minimized. [. . . ]