User manual MIELE KM 362

[. . . ] F Cet appareil est également homologué dans des pays différents de ceux mentionnés sur l'appareil. Pour que l'appareil fonctionne parfaitement et en toute sécurité, il est important de disposer de l'exécution spécifique au pays et du type de raccordement approprié. Pour le fonctionnement dans un pays autre que celui spécifié sur l'appareil, veuillez vous adresser au service après-vente du pays où sera installé l'appareil. I L'apparecchio può essere usato anche in paesi diversi da quello indicato sull'apparecchio stesso. [. . . ] The high temperatures radiated by the hob could damage the appliance below. Spray canisters, aerosols and other inflammable substances should not be stored in a drawer under the hob. b A minimum safety distance must be maintained between the appliance and a cooker hood above it. See the manufacturer's operating and installation instructions for details. a minimum safety distance of 760 mm should be maintained between it and the appliance below. Safety distance above the appliance All dimensions in this instruction booklet are given in mm. Keep these instructions in a safe place and pass them on to any future user/owner of the appliance. 6 Appliance dimensions and worktop cut-out KM 360 G / KM 362 G a Building-in depth b Mains connection box c Gas connection R 1/2 - ISO 7-1 (DIN2999) 7 Appliance dimensions and worktop cut-out KM 360-1 G / KM 362-1 G a Building-in depth b Mains connection box c Gas connection R 1/2 - ISO 7-1 (DIN2999) 8 Appliance dimensions and worktop cut-out KM 361 G / KM 363 G a Building-in depth b Mains connection box c Gas connection R 1/2 - ISO 7-1 (DIN2999) 9 Appliance dimensions and worktop cut-out ^ Prepare the worktop cut-out as shown in the diagrams. Remember to maintain a minimum safety distance of 50 mm between the hob and the back wall and 100 mm between it and a side wall or tall unit to the right or left of the hob. (See "Warning and Safety instructions"). ^ Seal the cut surfaces with a suitable heat-resistant sealant to avoid swelling caused by moisture. If during installation, the corners of the frame are not flush with the worktop surface, the corner radius, Max R4 can be carefully scribed to suit. 10 Installation Building in the appliance ^ Place the gas hob in the prepared cut-out. ^ Feed the electricity connection cable through the cut-out and connect. ^ Make the gas connection, (see relevant section). Securing the appliance ^ Secure the gas hob with the brackets a supplied, see illustration. 11 Installation Do not let sealant get in between the hob frame and the worktop. This could cause difficulties if the hob ever needs to be taken out for servicing and possibly result in damage to the hob frame or the worktop. The sealing strip under the edge of the top part of the hob provides a sufficient seal for the worktop. 12 Electrical connection All electrical work should be carried out by a suitably qualified and competent person in strict accordance with national and local safety regulations. Installation, repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held liable for unauthorised work. Ensure power is not supplied to the appliance until after installation or repair work has been carried out. The appliance must only be operated when built-in. This is to ensure that all electrical parts are shielded. Do not connect the appliance to the mains electricity supply by an extension lead. These do not guarantee the required safety of the appliance. [. . . ] ^ Pull the jet out with a pair of pointed pliers. ^ Select the jets as shown in the table, fit, reversing the procedure, and secure. 21 Conversion to another type of gas After changing the jets ^ Assemble the removed burner parts in reverse order and check for leaks by operating the burner without the upper section of the hob in place (use a match to ignite the flame). ^ Then replace the upper section of the hob. KM 360 G / KM 362 G When replacing the stainless steel upper section: Position the upper section as shown in the illustration, pushing it forwards first of all and then backwards until the angle bracket a clicks into place underneath the lip b of the lower section. [. . . ]