User manual MIELE KM 371

[. . . ] Installation instructions Gas hobs KM 370 G / KM 370-1 G KM 371 G KM 390 G / KM 391 G To avoid the risk of accidents or damage to the appliance it is essential to read these operating instructions before it is installed or used for the first time. GiZ M. -Nr. 05 827 720 G This appliance can be used in countries other than those specified on the appliance. It is, however, set up for connection to the gas and electricity supplies in the countries specified. For use in other countries please contact the Miele spare parts or customer service department in your country. [. . . ] ^ Seal the cut surfaces with a suitable heat-resistant sealant to avoid swelling caused by moisture. If during installation, the corners of the frame are not flush with the worktop surface, the corner radius, Max R4 can be carefully scribed to suit. 12 Installation Building in the appliance ^ Feed the electricity connection cable through the cut-out and connect. ^ Place the gas hob in the prepared cut-out. ^ Make the gas connection (see relevant section). Securing the appliance KM 371 G / KM 391 G ^ Secure the gas hob at the front and rear with fixing brackets a supplied as shown. KM 370 G / KM 370-1 G / KM 390 G ^ Secure the gas hob at the front with fixing brackets a and rear with fixing brackets b supplied as shown. 13 Installation Do not let sealant get in between the hob frame and the worktop. This could cause difficulties if the hob ever needs to be taken out for servicing and possibly result in damage to the hob frame or the worktop. The sealing strip under the edge of the top part of the hob provides a sufficient seal for the worktop. 14 Electrical connection All electrical work should be carried out by a suitably qualified and competent person in strict accordance with national and local safety regulations. Installation, repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held liable for unauthorised work. Ensure power is not supplied to the appliance until after installation or repair work has been carried out. The appliance must only be operated when built-in. This is to ensure that all electrical parts are shielded. Do not connect the appliance to the mains electricity supply by an extension lead. These do not guarantee the required safety of the appliance. The voltage and connected load are given on the data plate. Ensure that these match the household mains supply. Connection should be made via a suitable isolator or a double pole fused spur connection unit which complies with national and local safety regulations and the on/off switch should be easily accessible after the appliance has been built in. If the switch is not accessible after installation (depending on country) an additional means of disconnection must be provided for all poles. For extra safety it is advisable to install a residual current device (RCD) with a trip current of 30 mA. When switched off there must be an all-pole contact gap of 3 mm in the isolator switch (including switch, fuses and relays). This appliance is supplied for connection to a single phase 230-240 V 50 Hz supply with a 3-core cable. The wires in the mains lead are coloured in accordance with the following code: Green/yellow = earth Blue Brown = neutral = live WARNING THIS APPLIANCE MUST BE EARTHED 15 Electrical connection Important The electrical safety of this appliance can only be guaranteed when continuity is complete between the appliance and an effective earthing system, which complies with local and national regulations. [. . . ] Contact your local gas supplier if the natural gas connection pressure is less than 18 mbar or higher than 25 mbar. For U. K. and IE Main jet Ø Small jet Ø Natural gas H Small burner Medium burner Large burner Wok Liquid gas Small burner Medium burner Large burner Wok 0. 50 0. 65 0. 85 0. 97 / 0. 37 0. 23 0. 32 0. 40 0. 52 / 0. 23 0. 76 1. 00 1. 29 1. 40 / 0. 68 0. 39 0. 42 0. 54 0. 88 / 0. 42 25 Conversion to another type of gas Changing the jets Disconnect the gas hob from the electricity supply by switching off at the socket and withdrawing the plug or by removing the mains fuse. Changing the main jets Small, medium and large burners ^ Take off the pan support, burner cap b and the burner head d. ^ Using an M7 socket spanner unscrew the main jet e. [. . . ]