User manual MIELE KM 531

[. . . ] Operating and Installation instructions Ceramic hobs KM 530 / KM 537 KM 540 / KM 541 / KM 542 / KM 543 KM 544 / KM 545 / KM 547 / KM 548 KM 550 / KM 551 / KM 552 / KM 553 To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time. GHirZ M. -Nr. 06 069 910 Contents Guide to the appliance . 10 KM 537 / KM 550 / KM 551 KM 552 / KM 553 . 22 Cleaning and heating up for the first time . [. . . ] If you wish to use this feature, you will need to alter the factory setting (see "Programming - P5"). To activate Stop and Go: ^ Touch the $ sensor until you hear two consecutive beeps. Be careful not to continue touching the $ sensor for too long, as this will activate the safety lock. The indicator lamp for the safety lock will start to flash. The power of the cooking zone in use will be reduced to setting 1, and a 1 will appear in the corresponding cooking zone display. If automatic switch-off is programmed for a cooking zone, activating Stop and Go will interrupt the count down to the switch-off time. When Stop and Go is deactivated, the automatic switch-off programme time will continue to run without further interruption. If a minute minder time has been set, this will continue running and will not be affected by Stop and Go. To deactivate Stop and Go: ^ Touch the safety lock sensor $ until the indicator lamp goes out. The cooking zones will now run at the level that was previously set. 31 Safety features Safety switch-off Safety switch-off with an over-long cooking time Your hob is fitted with a safety switch-off feature in case you forget to switch it off yourself. If one of the cooking zones is heated for an unusually long period of time (see chart), and the power settings are not altered, the hob will switch itself off automatically and the appropriate residual heat indicator will appear. Power setting* Maximum operating time in hours 10 5 5 4 3 2 2 2 1 Safety switch-off if the sensors are covered Your hob will switch off automatically if one or several of the sensors remain covered for longer than 10 seconds, for example, by finger contact, food boiling over or by an object such as an oven glove or tea towel. An audible tone will sound every 30 seconds (for a maximum of ten minutes) and an F will flash in the display for the sensor which is covered. 1 / 1. 9 ^ Clean the control area or remove the obstruction. This will turn off the tone and the F will go out. ^ Switch the hob back on again with the ON/OFF sensor s. The cooking zones can now be used again as normal. * The power settings with a dot after the number are only available if the power setting range has been extended (see "Programming - P6. "). ^ To use the cooking zones again, switch the hob back on in the usual way. 32 Safety features Overheating protection Each cooking zone is equipped with overheating protection. An internal temperature limiter switches off the heating elements in the cooking zone before the ceramic surface overheats. Once the ceramic has cooled down to a safe level the heating will automatically switch back on again. Overheating can be caused by: ­ switching on a cooking zone without a pan on it. ­ the base of a pan not sitting evenly on the cooking zone. [. . . ] 2 mm). e Worktop f Hob g Gap Corner radius of the worktop ß R4 64 Installation Solid wood and tiled worktops ^ Make the worktop cut-out as shown in drawings. ^ Fix the wooden frame a 7mm below the top edge of the worktop (see diagram). ^ Feed the hob connection cable down through the cut-out. ^ Seal the remaining gap g with a silicone sealant that is heat-resistant to at least 160 °C. As the ceramic glass and the worktop cut-out have a certain dimensional tolerance, gap g can vary (min. [. . . ]