User manual MINOURA M20-D

[. . . ] You need to replace the left side coupling (UF-8) with optional "Left Side Coupling for Hub Nut Axle". Use correct tools (10mm spanner & M4 hex wrench). · Use the supplied rear quick release skewer for maximum stability. Minoura is not responsible for any problem caused from using your own skewer. [. . . ] Any damage or problem caused by transporting process is not covered under warranty. Any damage from shipping or moving must be made to the shipping company. - Page 2 - M20-D Schematics UF-9 UF-6 UF-7 BF-8 BF-4 UF-8 BF-6 BF-4 EM-1 MF-3 EM-3 EM-4 BF-6 EM-13 M5-2 EM-2 EM-11 LM-10 EM-5 EM-19 EM-17 EM-20 BF-4: LegRubberCover(Red) BF-6: LegRubber EM-1: OuterCap EM-2: AxleHolder EM-3: DriveRoller&Bearing EM-4: MainHousing EM-5: AlloyRotor EM-11:ConnectingPlate EM-13: esistanceAdjustLever R EM-17: lywheelDisc(0. 6kgs) F EM-19: agnetPlate(forM20) M EM-20: lywheelCover(WhiteforM20) F BF-8: M20MainFrame(White) UF-6: RightSideCoupling&ClampLever UF-7: ClampLeverGuide UF-8: LeftSideCoupling(forQ/Rskewer) UF-9: CouplingLockRing(Red) M5-2: RubberFootCap(29mm) MF-3: RollerPressureAdjustKnob LM-10:BasePlate - Page 3 - How To Setup Your M20-D Trainer Required Tools: 1x10mmSpanner 1xM4HexWrench 1. Replace your rear wheel quick release skewer to the supplied one. ! Minoura guarantees the stability only when using the supplied skewer due to the coupling inner shape. If your bike is not equipped with quick release skewer and it's a hub nut type, replace the left side coupling (UF-8) to the optional "Left Side Coupling for Hub Nut Axle". Minoura doesn't guarantee the stability if you don't replace the left side coupling. You don't need the supplied quick release skewer if your wheel is a hub nut type. It's not possible to convert your wheel from the hub nut type to the quick release skewer type unless replacing the hub. ! 2. Install the Roller Pressure Adjust Knob set (MF-3) to M20-D frame. A) Insert the flat washer and acorn spring into the knob bolt first, then screw the knob set to the welded nut on the bracket. ! Make sure the acorn shaped spring direction is as shown in Fig. Failure will cause difficulty on rotating. (Fig. A) ! If you feel some difficulty of the vertical action of the Mag resistance unit, slightly loosen the pivot bolt which connects the Mag unit to the frame. It may cause injury to your finger when you lift up the trainer. 3. Fully open both legs and place M20-D on a flat and level floor. B) At this moment, make sure all 4 foot are contacting the floor at once to sit on the floor stable. - Page 4 - (Fig. B) 4. Place your rear wheel in between the couplings. 1) Loosen the lock ring (UF-9) to allow the left side coupling (UF-8) be free. C) 2) Pull up the quick hub clamp lever (UF-6) to retract the right side coupling. D) 3) Insert the left side (quick lever side) skewer into the left side coupling first. The quick lever shaft must be inserted into the cut-out on the coupling to hold the bike stable. Turn the coupling to adjust the cut-out position. 4) While keeping this position, slowly come down the bike to align the right side acorn nut to the right side coupling. 5) Push down the quick hub clamp lever to hold the rear wheel. E) If you start feeling resistance when the lever comes at 4 o'clock position, it's correct. If the clamping hub is too tight or too loose due to wrong position of the left side coupling, pull up the lever to release the bike, adjust the left side coupling position and try clamping the hub again. 6) Lastly, tighten the lock ring to fix the left side coupling position. [. . . ] N) (Fig. L) (Fig. M) (Fig. N) - Page 6 - !! If the rear tire has touched any other parts than the Drive Roller, the part may be damaged and your tire will wear out quickly. It is impossible to adjust the rear wheel position by adjusting the left side coupling position. It just works to adjust the coupling distance. 5. To remove the bike from M20-D, loosen the knob then lift up om the clamp. If you remove the bike without changing the roller position, the next installation may become difficult because the rear wheel has been pushed forward by the roller. How To Adjust Resistance Level M20-D provides 3 different resistance levels to suit your training level. [. . . ]