User manual MINOURA M80-R

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual MINOURA M80-R. We hope that this MINOURA M80-R user guide will be useful to you.

Lastmanuals help download the user guide MINOURA M80-R.


Mode d'emploi MINOURA M80-R
Download

You may also download the following manuals related to this product:

   MINOURA M80-R SCHEMA (127 ko)
   MINOURA M80-R PERFORMANCE DATA 10-2010 (49 ko)

Manual abstract: user guide MINOURA M80-R

Detailed instructions for use are in the User's Guide.

[. . . ] · Use on flat and level floor or ground for your safety. · Adjust the roller pressure to the rear tire properly in order to maximize your tire life. Tire and roller contact will eventually wear both your tire and the trainer roller. · Check and adjust the remote shifter cable tension when you cannot set at L or H even though you turn the shifter lever. [. . . ] A) Remove the pre-installed bolt from Base Plate (LM-10). Attach Mag unit to the bracket on frame, align the holes, and put through the bolt. Tighten the bolt with 10mm spanner and M4 hex wrench. ! Do not overtighten the bolt, otherwise the Mag unit will not move smoothly even if you rotate the knob. If properly installed, ` the Mag unit will come down slowly with its own weight when you release it. (Fig. A) Install the knob set to the welded nut on the bracket. ! Make sure the acorn shaped spring direction is as shown in Fig. Failure will cause difficulty on rotating. 3. Fully open both legs and place M70-R/M80-R on a flat and level floor. B) At this moment, make sure all 4 foot are contacting the floor at once to sit on the floor stable. - Page 4 - (Fig. B) 4. Place your rear wheel in between the couplings. 1) Loosen the lock ring (UF-9) to allow the left side coupling (UF-8) be free. C) 2) Pull up the quick hub clamp lever (UF-6) to retract the right side coupling. D) 3) Insert the left side (quick lever side) skewer into the left side coupling first. The quick lever shaft must be inserted into the cut-out on the coupling to hold the bike stable. Turn the coupling to adjust the cut-out position. 4) While keeping this position, slowly come down the bike to align the right side acorn nut to the right side coupling. 5) Push down the quick hub clamp lever to hold the rear wheel. E) If you start feeling resistance when the lever comes at 4 o'clock position, it's correct. If the clamping hub is too tight or too loose due to wrong position of the left side coupling, pull up the lever to release the bike, adjust the left side coupling position and try clamping the hub again. 6) Lastly, tighten the lock ring to fix the left side coupling position. F) (Fig. F) (Fig. D) (Fig. C) (Fig. E) ! Both left and right side couplings are designed to suit the supplied quick release skewer. The left side coupling must fit perfectly in the skewer head to get correct stability. G) (Fig. G) Any skewer type which lever is located on the end of the axle (Fig. H) or the lever will not be bent over right angle (Fig. I) cannot be used on M70-R/M80-R. ! Precisely adjust the left side coupling position to keep the correct thightness of rear hub clamping. Too tight setting will cause damage to both M70-R/M80-R and your bike frame. [. . . ] O-1) 2. Flip up the lever to lock (see Fig. O-2). following section. If it is loosened, adjust the band tighter as per instructed in the 3. The soft fabric band is pre-adjusted to fit normal 22mm diameter handlebar. If you need to mount onto an oversized or specially shaped handlebar or stem, adjust the band (see Fig. At this moment, we suggest you to slide the guide pin downward (see the column) to loosen the band for easier work. Decrease 1 2 1 (Fig. O) 3 2 (Fig. P) (Fig. Q) Increase 4. To increase the resistance, twist the lever toward "H". To decrease the resistance, twost the lever towawrd "L". [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MINOURA M80-R

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual MINOURA M80-R will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag