User manual MITSUBISHI 4G1

[. . . ] A red LED will appear to indicate charging is in progress. The battery should be charged before using the phone for the first time. Batteries last longer and perform better when allowed to discharge fully at least once a week. USING THE BATTERY GENERAL INFORMATION: The phone is powered by a rechargeable battery. To ensure maximum benefit from your new phone and to get better talk and standby times, it is important that you regularly charge and discharge the battery as instructed in this guide. RECHARGING THE BATTERY Caution: Use only the Mitsubishi AC adapter that was provided with your phone or the optional Mitsubishi Cigarette Lighter Adapter, CIG-P4. [. . . ] Step 3: Enter AKEY (626 digits) Step 4: STO+STO 934 6803747 -OKIf entered A-KEY is valid. 2sec Restart from Power ON sequence Invalid If entered A-KEY is invalid. Two (2) seconds Return to Step 1 Function: When you enter the "2539" followed by "FCN"+ "FCN", the phone enters "A-KEY programming mode" and "Telephone number" is displayed. 25 A-KEY is programmed by entering the six to 26 digit number provided by your carrier. The display will show the digits of the entered number. The "CLR" key can be used for editing. Momentary depression clears the last entered digit, and all digits are cleared by continuous depression. When the complete digit sequence has been entered, the "STO"+ "STO" key should be pressed to store the number. At this point the phone will validate the A-KEY based on the check sum. If the key is valid, the display shows "-OK-" for approximately two (2) seconds and restarts the phone from the Power-ON sequence. If the key is invalid, the display shows "Invalid" for approximately two (2) seconds and returns to the A-KEY re-entry state. Note: During the A-KEY programming mode the "END" key can be used to cancel and exit from this mode at any time. If the new A-KEY is entered, the existing A-KEY is overwritten by the new A-KEY. Once the A-KEY is programmed, it may not be viewed through the display or any device attached to the phone. FUNCTION MENU User action: FCN + FCN Menu w To RCL RCL -MenuPush v/w w/v (FCN FCN) (Standby only) Action FCN 1 Own Tel w/v FCN Tel:123 4567890 26 FCN 2 Alpha w/v FCN Alpha Input FCN 3 Redial w/v FCN Redial ON FCN 4 System w/v FCN System Pref A FCN 5 AutoAns w/v FCN AutoAns OFF FCN 6 Lock v w FCN Lock Code FCN 7 Last w/v FCN Last MMmSSs FCN 8 Oper w/v FCN Oper HHHhMMm FCN 91 Restr. w/v FCN Security Code Security Code Restr. · If the call restriction level is Recall 1-39 or Receive Only, this function is not available. The following message will appear on the display when call restriction is selected: Alpha N. A. Example (b): Add name to a stored number Address 12 Number "7112340" Add name "CEW" Display 12: 7112340 7112340 Alpha Input 12: ALPHA Operation RCL 12 CLR to exit RCL mode FCN + 2 One second later Enter alphabet CEW ALPHA 32 STO STO 7 112340_ Stored Addr. 12 Example (c): Edit a stored name and number Address 28 Operation RCL 28 CLR to exit RCL mode FCN + 2 One second later Edit name STO Edit Number STO Number "4975646" Display 28:MELC 4975646 4975646 Alpha Input 28: MELCO ALPHA Name "MELCO" M-CEW ALPHA 4 974656_ Stored Addr. 28 Function: A new character and number can be added to the last character of the stored name and number in this mode. 33 To delete the last character and number, press the "CLR" key. All characters and numbers are cleared by continuous depression. Note: · · During this editing mode no calls can be made. If all characters and numbers of the selected address are deleted by the "CLR" key, press the "STO" key to exit this mode. The following message is displayed: Erased Addr. 09 FCN 3: Automatic Redialing Direct Operation: FCN + 3 (Standby only) Redial ON Press */# key Redial OFF Function: When you enter "FCN" followed by "3", the phone enters the "Automatic Redial ON/OFF" mode and shows the current setting. The ON/OFF setting can be selected by pressing the "*" or "#" keys. In case of "Redial ON", the Automatic Redial function is active. Automatic Retry continues trying to access the system. The phone will attempt automatic retry 10 times with a three (3) second interval between each try when unable to access the cellular system. In order to complete your selection and exit from this mode, press the "STO, " "END, " or "CLR" key. 34 Note: This mode selection is stored while the phone is turned off. FCN 4: System A/B Selection Direct Operation: System Pref A Press FCN + 4 (Standby only) */# key System Pref B Press */# key System H only Press */# key System Only A Press */# key System Only B Function: When you enter "FCN" followed by "4", the phone enters the "System A/B Selection" mode and shows the current setting. [. . . ] If a damaged antenna comes into contact with the skin, a minor burn may result. Consult your manual to see if you may change the antenna yourself. If so, use only a manufacturer approved antenna. Otherwise, take your phone to a qualified service center for repair. [. . . ]