User manual MITSUBISHI 550U

[. . . ] LCD PROJECTOR MODEL XL650U XL550U User Manual XL650 XL550 This User Manual is important to you. Please read it before using your projector. ENGLISH CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE: SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE. WARNING Use the attached specified power supply cord. If you use another power supply cord, it may cause interference with radio and television reception. [. . . ] When AUTO is selected, the appropriate video format is automatically selected depending on the input signal. If the image isn't displayed correctly, select the desired video format manually. Select to change the SETUP mode automatically. · When 7. 5% is chosen, the brightness is decreased by the set-up cancel function for the U. S. Choose ON when connecting the projector with a device equipped with the SCART terminal that can output RGB signal. SCART terminal is used mainly in Europe. (Available only for the input signal from the COMPUTER/COMPONENT VIDEO IN-1 terminal. ) Use to select the language used in the menus. Use to reset the settings of the menu (excluding IMAGE CAPTURE, PASSWORD FUNCTION and LANGUAGE) to the factory setting values. CINEMA MODE can be adjusted only when a TV60, TV50, 480i or 576i signal is being displayed. When SCART INPUT is set to ON, nothing is output to the external monitor. When SCART INPUT is set to ON, normal computer signals aren't projected. Use a SCART-BNC (or SCART-Mini D-SUB 15-pin) cable (option) when connecting this projector with an AV device equipped with the SCART terminal. Some AV devices equipped with the SCART terminal aren't compatible with this projector. EN-25 ENGLISH Menu operation (continued) 4. SIGNAL menu opt. SIGNAL - USER menu opt. 5. INFORMATION menu opt. SIGNAL HORIZ. TRACKING RGB RGB SIGNAL 0 0 0 0 RGB 100% OFF OK ? INFORMATION 0H 1 1 AUTO OFF 0 0 0 RGB USER CLAMP POSITION CLAMP WIDTH VERT. SYNC LPF SHUTTER(U) SHUTTER(L) SHUTTER(LS) SHUTTER(RS) LAMP TIME (LOW) INPUT RESOLUTION VERTICAL FREQUENCY HORIZONTAL FREQUENCY H V COMPUTER2 1024x768 75. 04 Hz 60. 02 KHz 5wire COMPUTER INPUT OVER SCAN HOLD USER 0 SYNC. TRACKING COMPUTER INPUT SETTING 0-999 0-999 0-31 0-9999 AUTO RGB YCBCR/YPBPR OVER SCAN HOLD USER CLAMP POSITION CLAMP WIDTH VERT. SYNC 100%-90% OFF / ON 1-255 1-63 AUTO / OFF FUNCTION Use to adjust the horizontal position of the projected image. Use to adjust the vertical position of the projected image. Use to eliminate flickering or blur, if appears, viewing the projected image. Use to eliminate vertical wide stripes, if appears, viewing the projected image. The proper setting is automatically selected. Select this option when connecting the projector to high definition video equipment having R, G, and B output terminals. [. . . ] 1 2 3 4 5 6 7 8 9 Name TXD RXD GND I/O IN OUT - COMPUTER/COMPONENT VIDEO IN-1/IN-2 (Mini D-SUB 15-pin) 5 1 Pin No. R(RED)/CR G(GREEN)/Y B(BLUE)/CB GND GND GND GND GND DDC 5V (*1) GND GND DDC Data (*1) HD/CS (*1) VD DDC Clock DVI-D (HDCP) (DVI-D 24-pin) 16 24 17 9 6 11 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 8 1 PIN No. TMDS DATA 2TMDS DATA 2+ TMDS DATA 2 Shield DDC Clock DDC Data TMDS DATA 1TMDS DATA 1+ TMDS DATA 1 Shield - PIN No. 13 14 15 16 17 18 19 20 21 22 23 24 Spec. [. . . ]