User manual MITSUBISHI CP3800DW

[. . . ] Do not place the printer where chemical reactions occur, such as in a laboratory. Do not set up the printer where there is salinity or corrosive gas in the air. The printer must sit on a firm, level surface where there is ample ventilation. Do not put anything on the top of the printer. [. . . ] Turn on the power. CAUTION Please use the power cable that came with the printer, and be sure to attach the ground wire. 9 Sett ng Setting Up the Printer the Printer Setting the Printer Paper and Ribbon Type 8inch Paper Width: 203mm Ribbon Width: 210mm CAUTION Set the paper and ribbon without putting them directly on the work surface. Any dust or dirt could get inside the printer and adversely affect the print quality. 10 Setting Setting Up the Printer the Printer Setting Printer Setting the Media 1. Release the Open Lever, and pull out the mechanism unit. Open Lever 2. Open the Paper Release lever. Paper Release Lever 3. Remove the entire paper cassette unit. 11 Setting Setting Up the Printer the Printer Setting Printer 5. Install the new roll of paper on the paper holder. When installing it, make sure there are no gaps between the paper and the holder. Make sure the paper is not sticking out. If the end of the roll is uneven (with paper sticking out), remove it from the holder, and flatten it. No gaps × Check for uneven ends Check for uneven ends × 6. Set the paper holder into the paper cassette. (Set it firmly all the way in) Set the paper in the direction indicated below. Paper direction Seal 12 7. Remove the tape, and advance the roll as indicated by the arrow. Set the end of the paper about 5mm beyond the roller. When doing this, insert the paper straight along the seal. If it isn't inserted straight, the paper will be crooked, which could cause white line on the edges of the print, ribbon wrinkles, and register slippage. Sett ng Up the Printe Setting Up the Printer Setting the Printer Path of the paper As seen from above 8. Set the paper cassette into the printer. × 13 9. Turn the paper in the direction of the arrow. When it is advanced enough, the buzzer will beep, and the flashing LED (orange) will go out. It is easier to set if the paper is turned while securing the holder with one hand. Setting Setting Up the Printer the Printer Setting Printer 10. The printer will not operate without the scrap box. If the mechanism unit is closed without the scrap box attached, there will be a "No Scrap Box Error", and the LED will flash (red). CAUTION The printer will not operate without the scrap box attached. When the scrap box is removed, do not insert your fingers in the cutter at the top. [. . . ] Never use benzenes or thinners other than ethyl alcohol, as they may permeate the resin. 21 Specifications Model Print type Print mode Resolution 8×4 8×5 8×6 8×8 8×10 A4 8×12 8×10 8×12 8×10 A4 8×12 Print size Print sheet Print time Ribbon type Interface Driver-compatible OS Dimensions Weight Power Power consumption Noise Operating Environment CP3800DW Thermal dye sublimation transfer High-speed mode High quality mode 300×300dpi 300×600dpi 203×102mm 203×127mm 203×152mm 203×203mm 203×254mm 203×297mm 203×305mm 130 sheets 110 sheets Approx. 46 sec YMC+overcoat USB2. 0 Windows 2000/XP 322mm W ×366mm D × 170mm H Approx. 14kg(printer only) AC100V-240V 50/60Hz 120V 4. 0A 240V 1. 7A A-weighted sound pressure level < 70dB: " less than 70 dB" Temp. 5 ­ 35 degrees C in natural conditions Humidity 35 ­ 80% with no condensation *These specifications may be changed without prior notice. 22 Information on servicing the printer For questions regarding operation and servicing of the printer, contact the dealer where the printer was purchased, or consult at the following: MITSUBISHI DIGITAL ELECTRONICS AMERICA, INC. [. . . ]