User manual MITSUBISHI CP9800DW-S

[. . . ] DIGITAL COLOR PRINTER MODEL CP9800DW-S OPERATION MANUAL THIS OPERATION MANUAL IS IMPORTANT TO YOU. PLEASE READ IT BEFORE USING YOUR DIGITAL COLOR PRINTER. Hereby, Mitsubishi Electric Corporation, declares that this digital color printer is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. This digital color printer complies with the requirements of the EC Directive 89/336/EEC, 93/68/EEC and 2006/95/EC. The electro-magnetic susceptibility has been chosen at a level that gains proper operation in residential areas, on business and light industrial premises and on small-scale enterprises, inside as well as outside of the buildings. [. . . ] Setting Function 1 OFF Auto feed & cut mode When the door is closed after the print paper is installed with this unit powered on, this unit automatically carries out paper feed & cut operation. ON Manual feed & cut mode 2 OFF Set this switch to OFF. ON 12345678 FEATURES CONNECTIONS PREPARATION TROUBLESHOOTING OTHERS CONTENTS 10 BEFORE OPERATION Before printing, PRECAUTIONS 1 Install the print paper to this unit. (See below. ) 2 Position the adjustable paper guides. (See page 13. ) 3 Install the ink ribbon to this unit. (page 14-15) INSTALLATION OF PRINT PAPER Spacers 2 For the usage of the spacers, see the Quick Setup Guide. Remove the cushions put between the paper flange and spacer when using the spacers. Spacer Latch How to attach the spacers 1. Attach the spacer with the paper flange's stoppers retracted. Turn the spacer until the latches are locked. When you remove the spacers from the paper flanges, follow the above procedure in reverse. Paper flange FEATURES CONNECTIONS PREPARATION 1 Attach the supplied paper flanges to both sides of the print paper. When you pinch the latches on the paper flange, the stoppers retract into the shaft. Attach the flanges to the print paper with the stoppers retracted. Make sure that the flanges are attached to the print paper securely, and release the latches. NOTE Take care not to pinch your fingers. Do not remove the sticker on the print paper yet. Any slack in the print paper may degrade the print quality. Sticker · · CAUTION When placing the print paper, remove one flange and keep the print paper upright on its side with no flange. When you put the print paper sideways, it may roll and fall. This may cause injury. TROUBLESHOOTING · · · OTHERS CONTENTS INCORRECT NOTE · · Do not touch the thermal head. Fingerprints or dust on the thermal head will degrade the print quality. Fingerprints or dust on the paper's surface may degrade print quality and cause paper jams. CORRECT 11 BEFORE OPERATION 2 Press the POWER switch on the rear panel to turn on the power. PRECAUTIONS POWER switch 3 After the mechanical initialization is completed, press the DOOR OPEN button to open the door. Take the ink cassette in the printer out. FEATURES CONNECTIONS PREPARATION 4 Install the print paper into the unit. Make sure to install the print paper firmly. [. . . ] If the ink ribbon, print paper, or ink cassette can not be taken out, consult with your dealer. 19 CLEANING Cleaning as indicated below will help maintain stable printer operation and extend the printer's life. PREPARATIONS FOR CLEANING PRECAUTIONS 1 Press the POWER swich on the rear panel to turn on the power. 2 Press the DOOR OPEN button to open the door. 5 Press the POWER switch to turn off the power. Make sure to turn off the power before cleaning. FEATURES FILTER CLEANING Take out the filter from the printer by pinching the tab as shown in the figure, then clean both sides of the filter with a vacuum. After completing cleaning, insert it to the end with the marking of "TOP SIDE" up. CONNECTIONS PREPARATION THERMAL HEAD CLEANING Preparations Alcohol (isopropyl alcohol) Tissue paper (Fold in half about four times, and use the folded side to clean. ) Other : Cleaner pen (option)*, Cleaning ribbon (option)* * Please ask the dealer about options. [. . . ]