User manual MITSUBISHI DIAMOND PRO 91TXM

[. . . ] MITSUBISHI AUTO-SCANNING WITH DIGITAL CONTROL COLOR DISPLAY MONITOR MODEL TFW9105SKTKW USER'S GUIDE For future reference, record the serial number of your display monitor in the space below: SERIAL No. The serial number is located on the rear cover of the monitor. CAUTION The power cord provided with this monitor is designed for safety and must be used with a properly grounded outlet to avoid possible electrical shock. Do not remove the monitor cabinet as this can expose you to very high voltages and other hazards. ANMERKUNG: Dieser Monitor erfüllt die Anforderungen der deutschen Ergonomie-Norm ZH1/ 618/10. 80 bei Verwendung der beiden folgenden Timing: Auflösung Videoeingang 1600x1200 Analog RGB, 0. 7Vs-s fH(kHz) fv(Hz) Interlace/Non-Interlace 89. 1 72. 0 Non-Interlaced Aus ergonomischen Gründen wird empfohlen, die Grundfarbe Blau nicht auf dunklerem Untergrund zu verwenden (schlechte Erkennbarkeit, Augenbelastung bei zu geringem Zeichenkontrast). Bei hellem Hintergrund empfehlen wir aus ergonomischen Gründen nur Vertikalfrequenzen größer oder gleich 70Hz zu verwenden. [. . . ] Power off, the monitor and the computer. Connect the one end of the SC-B102 cable to the 15-pin connector on the VGA controller card. Connect the other end of the SC-B102 cable to the DB9-15P receptacle on the back of the monitor. Power on the computer, then the monitor. After using the system, power off the monitor, then the computer. Computer VGA Compatible System BNC D-SUB Serial R G B COMP. HD VD Sync 75 1k DB9-15P DB9-15P Power Cord CABLE SC-B102 Figure 3. CAUTION The socket-outlet shall be installed near the equipment and shall be easily accessible. During servicing, disconnect the plug from the socket-outlet. Méme si le moniteur est mis hors tension il reste toujours alimenté. La prise secteur devrait ainsi ètre facilement accssible en cas d'urgence. 11 2. 2. 2 Connecting to An Apple Macintosh Centris, Quadra, and Apple Macintosh II Family Figure 4 shows the SC-B102 cable and AD-A205 Adapter to the video port in an Apple Macintosh. Power off, both the monitor and the computer. Set the DIP switches of Macintosh Adapter according to the setting chart. (See 7. 4 Macintosh Adapter AD-A205 settings) 3. Connect the 15-pin (DB-15P) end of the AD-A205 Adapter to the straight 15-pin connector on the Macintosh video port on the CPU or on the video board. Connect the sub-miniature 15-pin (DB9-15P) end of AD-A205 Adapter to the SC-B102 cable. Connect the other end of the SC-B102 cable to the DB9-15P receptacle on the back of the monitor. Power on the Macintosh, then the monitor. After using the system, power off the monitor, then the Macintosh. BNC D-SUB Serial R G B COMP. HD VD Sync 75 1k Apple Macintosh Computer Macintosh DB-15P Adapter DB9-15P AD-A205 DB9-15P Power Cord CABLE SC-B102 Please see APPENDIX (7. 4 Macintosh Adapter AD-205 settings). Figure 4. 12 2. 2. 3 Connecting to a Unix Workstation & Third Party Graphics Card Figure 5 shows the SC-B102 or "75 " coaxial cable (not supplied) connection to the graphics video card (PC-CAD and workstation). Power off, both the monitor and the computer. Connect one end of the SC-B102 cable or the "75 connector on the CPU, or on the video board. Connect the other end of the SC-B102 cable or the "75 " coaxial cable to the " coaxial cable to the output DB9-15P receptacle or the BNC receptacles on the back of the monitor. [. . . ] · Rear BNC cables are misconnected. · Front (OSD) Input video signal level select is not at the appropriate position for your graphics adapter output. (0. 7V or 1. 0Vp-p) NOTE: Two fine horizontal lines may be visible on the screen. This is not a fault or defect of the monitor and is normal for all aperture grille type displays. The fine lines are the shadows of Damper Wires which are used to reduce the susceptability of the DIAMONDTRON CRT's aperture grille to shock or vibration. 25 6 SPECIFICATIONS 55cm/21"(50cm/19. 7" Diagonal Viewable Image) aperture grille In-line 90° CRT Red, Green, Blue EBU (medium short persistence) Aperture grille pitch 0. 28mm Face Plate Anti-glare, Anti-reflection and Anti-static coating Focusing method Dynamic Beam Forming (DBF) INPUT SIGNAL Video 0. 7 and 1. 0Vp-p analog RGB Sync Sync. [. . . ]