User manual MITSUBISHI DX-TL4509EZ

[. . . ] DIGITAL RECORDER INSTALLERS MANUAL OTHERS MODEL DX-TL4509E DX-TL4509E(Z) THIS INSTRUCTION MANUAL IS IMPORTANT TO YOU. PLEASE READ IT BEFORE USING YOUR DIGITAL RECORDER. 1 ENGLISH Caution and care HEAVY OBJECTS SHOULD NEVER BE PLACED ON THE UNIT (E. G. , MONITOR) NEVER TOUCH OR INSERT ANY OBJECT INSIDE THE UNIT Touching the inside of the cabinet or inserting foreign objects of any kind through the disc loading slot or ventilation holes not only creates a safety hazard but can also cause extensive damage. PROTECT THE POWER CORD Damage to the power cord may cause fire or shock hazard. If the power cord is damaged, turn OFF the MAIN switch and carefully unplug the cord by holding the main plug. [. . . ] External & MD-B: Starts alarm recording when the motion B is detected while the ALARM IN terminal is grounded. External: Starts alarm recording only when the ALARM IN terminal is grounded. External / MD-A: Starts alarm recording when the ALARM IN terminal is grounded or the motion A is detected. External / MD-B: Starts alarm recording when the ALARM IN terminal is grounded or the motion B is detected. MD-A: Starts alarm recording only when the motion A is detected. MD-B: Starts alarm recording only when the motion B is detected. Frame recording and field recording · · Alarm Input This item is used to stop the alarm input manually. When setting "Alarm Input" to "Off, " the alarm input is stopped for 5 minutes. To set the <Recording> menu while the alarm recording occurs continuously, stop the alarm input first to stop recording. "Alarm Input" function is available for ALARM IN terminal on the rear panel, motion detection, emergency recording, and communication port. To cancel the prohibition of alarm input manually, set it to "On" and then exit the <Recording> menu. It is cancelled automatically after 5 minutes. Operations 51 ENGLISH Recording (continued) Emergency Recording Setup This item is used to set the emergency recording settings. When the EMERGENCY terminal is grounded by the alarm sensor while both of the MAIN switch on the rear panel and the POWER button on the front panel are turned ON, emergency recording starts automatically overriding all the other settings even during timer recording or the unit is in stop mode. Emergency recording is not performed while the MAIN switch or POWER button is turned OFF or while timer recording stand-by mode. The setting of the <Recording> menu cannot be changed during normal recording or alarm recording. To change setting during recording, stop recording in case of normal recording. In case of alarm recording, when the "Alarm Input" in the <Recording> menu is set to "Off, " the alarm input is not accepted for 5 minutes. When you stop recording during this time, the setting change of the <Recording> menu is available. Setup Menu 1 Recording 5 Emergency Recording Setup D Emergency Record Settings Setup Menu Emergency recording 1) The picture grade is "L6-34KB" and the recording rate is set to the value obtained by dividing the maximum emergency recording rate by the number of specified cameras. When the LPA area is set in the main device, the emergency recording data is stored in the LPA area and is automatically locked in 512 MB unit including the emergency recording data in order to prevent overwriting the data. In LPA area, the data is always recorded at the rate set for alarm recording regardless of an input of the emergency signal. Therefore, when the emergency recording is started from the mid-part of the data block, the data recorded before the ground of the EMERGENCY terminal is stored in the locked area along with the emergency recording. When you set the long pre-alarm recording time without setting the LPA area, long pre-alarm recording is carried out using the internal memory for pre-alarm recording, so long pre-alarm recording is performed for the short time period regardless of the setting. When emergency recording is carried out using the LPA area, data is not stored chronologically and alarms are listed out of sequence. [. . . ] Picture data input from all the connected cameras is recorded sequentially. every 0. 005 second during normal recording. ) The example when setting a setup of each channel to "1 pps" 1 second C1-3 12:00:03~ C4-2 C3-2 C2-2 C1-2 1 second approx. 0. 005 second C4-1 C3-1 C2-1 C1-1 12:00:02~ Examples of time displayed during playback. approx. 0. 005 second 12:00:01~ Glossary 126 Specifications ENGLISH 2 1 2 1 1 Rated Power Supply . . . . . . . . . . . . . . . . . 100 to 240 V AC, 50/60 Hz Rated Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 9- 0. 4 A (100-240 V) Colour System . . . . . . . . . . . . . . . . . . . . . . . . . . PAL-type colour system. [. . . ]