User manual MITSUBISHI DX-TL8U

[. . . ] Digital Video Recorder WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. i User's Manual AVERTISSEMENT DANGER D'ÉLECTROCUTION NE PAS OUVRIR AVERTISSEMENT: POUR ÉLIMINER TOUT RISQUE D'ÉLECTROCUTION, NE PAS OUVRIR LE COUVERCLE (OU LA PARTIE ARRIÈRE). AUCUNE PIECE RÉPARABLE PAR L'UTILISATEUR NE SE TROUVE À L'INTÉRIEUR. [. . . ] Selecting Cancel 26 Digital Video Recorder Video Loss Settings (EVENT Video Loss Tab) Figure 17 Video Loss setup screen. The DVR checks to see if anything is obscuring the camera. Highlight the slider bar beside Check Obscuration, and use the Left and Right arrow buttons to adjust the setting. The sensitivity can be set from Never to 10 (extremely sensitive). The DVR can be set to react to video loss differently for each camera. Highlighting the box under the Actions heading and pressing the button allows you to set up event actions for video loss. Record Associate as many cameras with that camera as you wish. If the DVR detects video loss on the selected camera, it starts recording video from all the associated cameras. Alarm-Out Select between Alarm Output and Beep (DVR's internal buzzer) that you would like to activate and to sound whenever the DVR detects video loss on the selected camera. Notify You can toggle the individual notification items On and Off by highlighting that item and pressing the button. Highlight OK and press the button to accept your changes. PTZ Select the preset position for each PTZ camera, where you want PTZ cameras to move to when the DVR detects video loss on the selected camera's input. Spot Monitor Associate a camera with the Spot monitor. The DVR will display the associated camera on the Spot monitor whenever it detects video loss on the selected camera. NOTE: For the Record action, the camera you select should be set to the Event or Time & Event recording mode in the Record Schedule setup screen. NOTE: For the Alarm-Out action, the alarm output and beep you select should be set to the Event mode in the Alarm-Out setup screen (Schedule tab). NOTE: For the Notify action, the notify item you select should be enabled in the Notification setup screen and the DVR should be registered in the DX-PC For View (Remote Administration System). You can save your Video Loss changes by highlighting Save and pressing the exits the screen without saving the changes. button. Selecting Cancel 27 User's Manual Text-In Settings (EVENT Text-In Tab) Figure 18 Text-In setup screen. The DVR can be set to react to text input from devices such as ATMs (Automated Teller Machines) and POS (Point of Sale; i. e. , cash registers). This screen allows you to configure the DVR for each text-in device. Highlight the box under the Setup heading, and press the button. Selecting the Setup heading changes all the parameters excluding Port settings of all the text input channels. NOTE: The system performance might be affected when a large quantity of text inputs are detected from several channels at the same time. Highlight the box beside Port, and press the button. Select from None, RS232, RS485 and USB-Serial (1~8). NOTE: If you have set the Port as None, you will not be able to make any changes to the screen. NOTE: When using the USB to serial text-in device, do NOT remove the USB cable from the port while the system is running. Highlight Setup. . . , and press the button. Use the ATM or POS manufacturer's recommended settings when configuring the RS232, RS485 or USB-Serial ports. Highlight the box beside Text-In Product, and press the button. [. . . ] Enable Audio: Plays audio while playing back recorded video that has recorded audio. (Single-Screen Layout Only) Aspect Ratio: Changes the image aspect ratio. Deinterlacing: Using a deinterlace filter for interlaced video enhances image display quality by eliminating horizontal scan lines and noise in areas with motion. Anti-Aliasing Screen: Enhances image display quality by eliminating stair stepping (aliasing) effects in the enlarged image. NOTE: A camera name change in the Web Search mode does not affect the camera name set up on the remote site. [. . . ]