User manual MITSUBISHI EASYID70

[. . . ] OPERATOR USER´S MANUAL DPS TERMINAL Model MT1 series Software version 2. 0. 0 ENGLISH Rev 1. 6 For more information please visit www. mitsubishiphoto. com and www. easyphotosystem. com. Operator users manual TABLE OF CONTENTS 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1. 1 The best choice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1. 2 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1. 2. 1 Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The available layouts depend on the selected country (in settings of the system) and the paper size of the printer. Only one picture can be selected, and also only one layout can be chosen by the end customer. When the picture is selected, its automatically allocated in the selected layout to the right panel. In the center area is possible to check the cutting area of the layout rectangle. In order to fit better the picture inside every frame or rectangle, sometimes is better to rotate the picture. After pressing the "Finish order" button, a pop-up will appear in order to determine the amount of copies desired 25/74 Operator users manual 3. 7 Photo ID (Optional) Its highly recommended to follow the next steps to make an ID service. 3. 7. 1 Taking the pictures Before selecting the PhotoID service at the main screen, the operator should take the pictures to the customer. When using a digital camera with an USB cable connected to easyphoto: If an USB switch is being used between the camera and the easyphoto, this must be switched to the position where the connection between both devices is disabled, in order to allow the camera to take pictures. When an USB switch is not being used, the digital camera USB cable should be disconnected from the easyphoto. NOTE The behaviour of the camera when the USB cable is connected or disconnected may vary depending on the camera brand/model used. Also, the use of an USB switch is not always necessary. Please ask for more information to your dealer or installer. 3. 7. 2 Selecting the service Once the "Photo ID" button (in operator mode) is pressed, or the hidden area between language selection (flags) and prices is pressed, the Photo ID service is started. 26/74 Operator users manual 3. 7. 3 Selecting the picture source After this, depending on the system setup, its necessary to follow the source selection workflow or it can be avoided if the operator is using always the same digital picture files source (see the Administration and Settings chapter for more information). As instance, if the operator is using always the same digital camera connected through USB cable to the easyphoto, this can be indicated in settings and the application wont ask the operator where the pictures must be read from. It will search the pictures from the camera directly. There are several picture sources available: Digital Memory Card, USB memory device (both using the media card reader of the easyphoto system) and USB connection with digital cameras. NOTE The most common USB modes used by the digital cameras are Mass Storage and PTP connection. PTP connection works better when there are only a few pictures into the camera memory: its recommended to empty the camera memory after every session when using the PTP connection. There must be at least 1 picture in the camera in order to be able to read pictures from it, too. In order to know about each camera brand/model PTP compatibility, please check the camera specifications. 27/74 Operator users manual When using a PTP or Mass Storage mode compatible Digital Camera, the operator is requested to connect it as its shown in the next picture. If an USB switch is being used between the camera and the easyphoto, now it must be switched to the position where the connection between both devices is active. When an USB switch is not being used, the digital camera USB cable should be connected to the easyphoto. When using a PTP camera, this will detect now the connection with the easyphoto system and will change to picture source mode. In most of the cameras using the Mass Storage mode, they have to be manually switched to this mode at this time. NEW 3. 7. 4 Selecting the layout Afterwards, the layout must be chosen. [. . . ] Open the cover and press FEED button while Power ON 2. and wait for both LED (FEED and ERROR) blinking by return. Depress FEED then POWER LED ON, and ERROR LED OFF 4. Press FEED then, POWER LED OFF, and ERROR LED ON 5. [. . . ]