User manual MITSUBISHI FRONT SUSPENSION SPECIFICATIONS

[. . . ] Conduct this test on the left turn as well as on the right turn. Standard value (inner wheel when outer wheel at 20_) : <SPACE RUNNER> 22_10' <SPACE WAGON> 21_50' FRONT SUSPENSION - On-vehicle Service CAMBER, CASTER AND KINGPIN INCLINATION MB991004 33A-5 Standard value: Item Camber (difference between right and left wheel: less than 30') Caster (difference between right and left wheel: less than 30') Kingpin inclination SPACE RUNNER 0_00' ± 30' 2_45' ± 30' 11_ 27' SPACE WAGON - 0_10' ± 30' 2_50' ± 30' 12_ 49' NOTE 1. Camber and caster are preset at the factory and cannot be adjusted. If camber is not within the standard value, check and replace bent or damaged parts. [. . . ] With the coil spring held compressed by the special tools (MB991237 and MB991238), provisionally tighten the selflocking nut. Caution To prevent the special tool from damage, do not use an impact wrench to tighten the special tool bolt. Line up the holes in the strut assembly lower spring seat with the hole in the upper spring seat. NOTE The job is easily accomplished with a pipe. Correctly align both ends of the coil spring with the grooves in the spring seat, and then loosen the special tools (MB991237 and MB991238). FRONT SUSPENSION - Strut Assembly 33A-9 5. Using the special tool, tighten the self-locking nut to the specified torque. MB991682 MB991619 Specified torque: 69 - 78 Nm Caution Do not use an impact wrench as internal parts of the strut assembly will be loosened. INSPECTION D D D D 33200140064 Check the bearing for wear or rust. Check the rubber parts for damage or deterioration. Check the spring for deformation, deterioration or damage. Check the shock absorber for deformation. 33A-10 FRONT SUSPENSION - Lower Arm Assembly 33200160121 LOWER ARM ASSEMBLY REMOVAL AND INSTALLATION Caution *: To prevent bushings from breakage"the parts indicated by * should be temporarily tightened, and then fully tightened with the vehicle on the ground in the unladen condition. Post-installation Operation D Check the Dust Cover for Cracks or Damage by Pushing it with Finger. D Wheel Alignment Check and Adjustment (Refer to P. 33A-4. ) 6 5 88 - 108 Nm 39 Nm 2 1 24 - 33 Nm 88 - 108 Nm* 5 6 98 - 118 Nm 3 4 78 Nm 177 Nm AA" AB" Removal steps 1. Lower arm and knuckle connection AC" 5. Lower arm and front member connection "AA 6. Lower arm assembly FRONT SUSPENSION - Lower Arm Assembly REMOVAL SERVICE POINTS MB991406, MB990635 or MB991113 Ball joint Cord 33A-11 AA" TIE ROD END DISCONNECTION Caution 1. Loosen the nut of the special tool, but do not remove it. If it is removed, the ball joint thread will be damaged. Tie the special tool with a cord not to let it fall off. Nut Front member AB" STAY REMOVAL The stay is tightened together with the front member. After the stay is removed, tighten the bolts loosely to hold the front member. NOTE If the lower arm assembly has been removed, tighten the bolts loosely to hold the front member. Front member mounting bolts AC" LOWER ARM AND FRONT MEMBER DISCONNECTION To remove the connection bolts of the lower arm at the vehicle rear side, remove the front member mounting bolts, and then lower the front member. Stay Knuckle A INSTALLATION SERVICE POINT "AA LOWER ARM ASSEMBLY INSTALLATION 1. Install the lower arm assembly to the knuckle. Caution When installing the lower arm assembly, make sure that the ball joint stud (A) does not protrude 4 mm or more from the knuckle in order to prevent grease from flowing out. If grease has flown out of the dust cover by pushing the lower arm in the knuckle excessively, replace the dust cover. Check that there is no clearance between the knuckle and the dust cover. Lower arm assembly 33A-12 FRONT SUSPENSION - Lower Arm Assembly INSPECTION D D D D Check Check Check Check the bushing for wear and deterioration. [. . . ] Use the special tools to presss in the bushing. Position the bushing so that its hollow part is as shown. Press in the bushing until its outer tube top surface is lined up with the lower arm assembly. Piece of metal Bushing 60_ Hollow part Lower arm assembly 33A-14 STABILIZER BAR FRONT SUSPENSION - Stabilizer Bar 33200190137 REMOVAL AND INSTALLATION Post-installation Operation Check the Dust Cover for Cracks or Damage by Pushing it with Finger. 39 Nm 2 3 4 39 Nm 1 39 Nm Removal steps 1. Stabilizer link D Front member (Refer to GROUP 32. ) "AA 2. [. . . ]