User manual MITSUBISHI GB-24A FOR INITIAL SETTING WEB

[. . . ] Mitsubishi Electric Air-conditioner Control System Centralized Controller GB-24A Operation Manual for Initial Setting Web Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1-1 Terms Used in This Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1-2 Computer Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 Setting the Operating Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2-1 Setting the PC IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2-2 Setting the Web Browser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Performing Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3-1 Entering the User Name and the Password, and Connecting to the GB-24A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 4 Initial Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4-1 Setting the Current Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4-2 Setting Basic Information and External Input Functions . . . . . . . . . . . . . . . . . . 8 4-3 Group Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 4-4 Interlocked Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 4-5 Block Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 5 Functions 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 5-1 Error mail reports/E-mail communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 5-2 Settings for measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 6 Functions 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 6-1 Limiting the Set Temperature Operating Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 6-2 Night Mode (Silent Mode) Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 7 User Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 8 Registering a License for Optional Functions . . . . . . . . . . . . . . . . . . . . . . . . 30 Before using the web browser to set the GB-24A controller, please read this operation Manual carefully to ensure correct operation. Retain this manual for future reference. 1 Introduction Special features of Mitsubishi Electric Corporation's "Centralized Controller GB-24A" are that a PC connected to a LAN can be used to monitor the operation condition of air conditioners, perform air conditioner operations, and make initial settings. The document explains the procedures for performing initial settings for the Centralized Controller GB-24A using the web browser. 1-1 Terms Used in This Manual - "Click" refers to positioning the mouse cursor on the object (such as button or folder), pressing down, and releasing the left mouse button once. - Unless otherwise specified, the example screen images used in this manual are Windows XP® and Internet Explorer 6. 0 screen images. Note: Windows is a registered trademark or trademark of Microsoft Corporation USA in the United States and other countries. 1-2 Computer Requirements To monitor and operate air conditioners by web browser, computer must include the following requirements. [. . . ] will be displayed with a red frame (selected state), and select the contact No. to which the general equipment is connected. To disconnect the general equipment, select the interface device No. , and click the contact No. will be displayed in gray (unselected state). Note: A maximum of 16 general equipment can be registered in one group. Note: To change the registered units to general equipment in the group in which air-conditioners are registered, disconnect the air-conditioners first. (2) To change the icon, click the right or left arrow. (3) In the [Allow Operation] section, select whether to enable or disable the ON/OFF operation on the Web browser operation screen. Select [In batch and on individual group] to enable only when the collective operation is performed. Select [On individual group] to enable in each group. Select [No operation (Monitor only)] to disable. (4) In the [Monitor] section, select whether to display I/P to or from the general equipment on the monitor screen. 16 4-4 Interlocked Setting To interlock the operation of LOSSNAY with the run/stop status of the indoor units, click on [Initial Settings]-[Interlocked LOSSNAY] in the menu to bring up the Interlocked LOSSNAY screen, and enter the interlock conditions. Click [Save Settings] to send setting data to the GB-24A. Note: If the user logs in as a manager, the operations may be prohibited. Interlocked LOSSNAY Registration Register the interlocked ventilation equipment here. Click to bring up the registration screen. Interlocked Indoor Units Registration Register the indoor units to which LOSSNAY units are interlocked here. Click to bring up the registration screen. Refresh Read setting data from GB-24A. Save Settings Send setting data to GB-24A. (1) Click in the Interlocked LOSSNAY registration field to display the [Select a Unit Address] screen, and click on the numbers corresponding to the units to be registered. The ones that are selected will be shown with a yellow-green background. To cancel the selection, click on them again. Deselected items will be shown with a gray background. (2) Click on the Interlocked Indoor Unit Registration field to display the [Select Unit Addresses] for the indoor units, and click on the numbers corresponding to the units to be registered. The ones selected will be highlighted with a yellow-green background. To cancel the selection, click on them again. Deselected items will be shown with a gray background. Note: A maximum of 16 indoor units can be registered to operate with one ventilator. 17 4-5 Block Setting By performing block settings, multiples of air conditioner groups can be collectively monitored or operated from the Web. Bring up the Block Setting screen by clicking [Initial Settings]-[Blocks] in the menu, and register the groups in the block to utilize these features. Click [Save Settings] to send setting data to the GB-24A. Note: If the user logs in as a manager, some of the operations may be prohibited. Block Name Register the block name to be displayed on the Web screen here. Group Registration Register the groups to be included in the block here. Refresh Read setting data from GB-24A. Save Settings Send setting data to GB-24A. 4-5-1 Registering a block name In the [Block Name] field on the screen, register the block name to be displayed on the Web screen, using a name consisting of no more than 20 characters Note: The following characters cannot be used in the group name: < > & " ` 4-5-2 Registering a group in a block Click on the Group Registration field to display [Select Groups], and click on the numbers corresponding to the groups to be registered. The ones that are selected will be shown with a yellow-green background. [. . . ] Note: When setting all groups collectively, click [Batch operation] button, and input settings. 26 6-2 Night Mode (Silent Mode) Schedule Click on [Function2]-[Night Mode Schedule] in the menu to open the night mode (silent mode) schedule screen and make necessary settings to switch the outdoor unit operation mode to the night mode (low-sound operation), and set the night mode time interval. Use this mode when low-sound operation of the outdoor unit is preferable during night. Note: Make this setting only when all the units operate normally. When connection error occurs at the indoor or the outdoor unit, night mode target units may not be displayed normally. Depending on the type of outdoor units connected, this function may not be available. [. . . ]