User manual MITSUBISHI HD4000 RS-232C CODES

[. . . ] (3) The personal computer checks the command and confirms if the sent command has been executed or not. (4) This projector sends various codes other than the return code. When having a control sequence by RS232C, reject other codes from the personal computer. [. . . ] This command will not be executed in Stand-by mode. This command will not be executed in Stand-by mode. This command will not be executed in Stand-by mode. This command will not be executed in Stand-by mode. 72h 63h 64h 76h 76h 31h 31h 31h 31h 32h [Example] When setting the input signal to COMPUTER (Figures and symbols enclosed in quotation marks are ASCII codes. ): Sending commands from the PC, etc. 30 30 5F 72 31 0D '0' '0' '_' 'r' '1' ' ' 30 30 5F 72 31 0D '0' '0' '_' 'r' '1' ' ' Status code from the projector Description Command for setting the input signal to COMPUTER Command receipt confirmation (Command echo back) 5) Keystone commands (Not executable in stand-by mode. Possible only to read during muting. ) The keystone commands are used for the keystone setting of this projector with the value. The value will vary depending on the installation conditions, etc. ) ITEM ASCII KEYSTONE(Vertical) KS KEYSTONE(Horizontal) KSH HEX 4Bh 53h 4Bh 53h VALUE ±40 ±25 48h How to set the grade Use the ASCII codes to set the grade for setting data. Please refer to the table below for the HEX code. ASCII HEX '+' 2Bh '­' 2Dh '0' 30h '1' 31h '2' 32h '3' 33h '4' 34h '5' 35h '6' 36h '7' 37h '8' 38h '9' 39h 2 6) Remote commands (Not executable in stand-by mode. When the remote commands are sent while the splash screen is being displayed, the splash screen is only canceled. ) Some remote control operations can be achieved by the remote command codes. The remote commands have no data codes. Button's name on remote { } $ % MENU ENTER AUTO POSITION ASPECT BLANK ASCII r53 r2b r4f r59 r54 r10 r09 re2 ra6 HEX 72h 72h 72h 72h 72h 72h 72h 72h 72h 35h 32h 34h 35h 35h 31h 30h 65h 61h 33h 62h 66h 39h 34h 30h 39h 32h 36h Button's name on remote AV MEMORY 1 AV MEMORY 2 AV MEMORY 3 CONTRAST BRIGHTNESS COLOR TEMP. GAMMA SHARPNESS KEYSTONE ASCII re4 re5 re6 rd0 rd1 rd4 rd5 rd6 r43 HEX 72h 72h 72h 72h 72h 72h 72h 72h 72h 65h 65h 65h 64h 64h 64h 64h 64h 34h 34h 35h 36h 30h 31h 34h 35h 36h 33h [Example] When displaying the MENU selection bar (Figures and symbols enclosed in quotation marks are ASCII codes. ): Sending commands from the PC, etc. 30 30 72 35 34 0D '0' '0' 'r' '5' '4' ' ' 30 30 72 35 34 0D '0' '0' 'r' '5' '4' ' ' Status code from the projector Command operating the same as the MENU button Command receipt confirmation (Command echo back) Description 7) Password lock commands The password lock commands control the password lock. The password lock enabling or disabling command is sent with a 4-digit figure (password) added to the end of the data code. When the password lock is enabled or disabled successfully, the projector sends a return command comprising the data code, password, and "1" at the end. When enabling or disabling the password lock fails, it sends a return command with "0" at the end. There is no reconfirmation of the password. ITEM Password lock enabling/ disabling ASCII PSLOCK HEX 50h 53h 4Ch 4Fh 43h 4Bh VALUE 0****(Disabling), 1****(DISPLAY INPUT) 2****(MENU ACCESS) **** is a 4-digit figure (password). 8) Reading command diagram The projectors operating status, such as POWER-ON / OFF and the currently selected input terminal, etc. can be monitored. ASCII Function Data (Receive) vP 1 vP 0 vI r1 vI c1 vI d1 vI v1 vI v2 vPK 0 vPK 1 vSM 0 vSM 1 HEX Function Data (Receive) 50h 31h 50h 30h 49h 72h 31h 49h 63h 31h 49h 64h 31h 49h 76h 31h 49h 76h 32h 50h 4Bh 30h 50h 4Bh 31h 53h 4Dh 30h 53h 4Dh 31h POWER ON POWER OFF INPUT COMPUTER INPUT COMPONENT INPUT HDMI INPUT VIDEO INPUT S-VIDEO POWER ON/OFF INPOSSIBLE POWER ON/OFF POSSIBLE NO SIGNAL SUPPLIED SIGNAL SUPPLIED 76h 76h 76h 76h 76h 76h 76h 76h 76h 76h 76h The PC sends the command without attaching the data code to it. [. . . ] Refer to "Menu operation" in the User Manual for more details. 4 [Example 1] When setting the AUTO POWER ON to ON. (Figures and symbols enclosed in quotation marks are ASCII codes. ): Status code from the projector Command for setting the 30 30 41 50 4F 4E 31 0D '0' '0' 'A' 'P' 'O' 'N' '1' ' ' AUTO POWER ON to ON Command receipt confirmation (Command echo back) Description Sending commands from the PC, etc. 30 30 41 50 4F 4E 31 0D '0' '0' 'A' 'P' 'O' 'N' '1' ' ' The data code of BRIGHTNESS of USER of COLOR TEMP. [. . . ]