User manual MITSUBISHI HS-1096E

[. . . ] TIME LAPSE VIDEO CASSETTE RECORDER MODEL HS-1096E INSTALLATION AND OPERATION MANUAL Only video cassette tapes with the mark may be used with this model. This instruction manual is important to you. Please read it before using your video cassette recorder. ENGLISH This Time Lapse Video Cassette Recorder complies with the requirements of the EC Directive 89/336/EEC, "EMC Directive" and 73/ 23/EEC, "Low Voltage Directive", as amended by Directive 93/68/EEC. The requirements for the susceptibility according to EN 55024 and the requirements for interference according to EN 55022 are observed for the operation on residential areas, business, light industrial premises and in small scale enterprises, inside as well as outside of the building. All places of operation are characterised by their connection to the public low voltage power supply system. [. . . ] The suitable number of VCRs and cameras to be connected are shown below: Recording time mode L18H, L24H L30H, L40H VCR 3 5 Number of cameras Multiple of 3 Multiple of 5 Additional Features Memory backup in case of power failure This VCR includes a built-in backup memory, so the preset day and present time will remain in memory even if there is a power failure. However, if the power cord is disconnected for a long period of time (2-3 months), the present time may not be accurate. In this case, set the clock again. Info. REC REC REC REC REC REC · REC REC REC · 1. · <MAIN MENU> appears. <MAIN MENU> DISPLAY TIMER PROGRAM RECORDING SET UP REAR TERMINAL MAINTENANCE 2. Turn JOG to select REAR TERMINAL and turn SHUTTLE to the right. · <REAR TERMINAL> menu appears. <REAR TERMINAL> CALL OUT WRNG·TAPE END CLOCK OUT REC- 1 MODE OUT REC REC IN SERIES · <REAR TERMINAL> CALL OUT WRNG·TAPE END CLOCK OUT REC- 1 MODE OUT REC REC IN SERIES 3. Turn JOG to select REC IN and turn SHUTTLE to the right. Turn JOG to select SERIES or RECSTART/STOP and turn SHUTTLE to the right. · If the recording start signal is available on the switcher, select SYNC REC. After a power failure <REAR TERMINAL> CALL OUT WRNG·TAPE END CLOCK OUT REC- 1 MODE OUT REC REC IN REC-START/STOP 5. Turn JOG to select CLOCK OUT and turn SHUTTLE to the right. Turn JOG to select T/L REC and turn SHUTTLE to the right. Turn JOG to select F and turn SHUTTLE to the right. Turn JOG to select SYNC REC and turn SHUTTLE to the right. · <REAR TERMINAL> CALL OUT WRNG·TAPE END CLOCK OUT REC- 1 MODE OUT REC REC IN SERIES <REAR TERMINAL> CALL OUT WRNG·TAPE END CLOCK OUT T/L REC- 1 MODE OUT REC REC IN SERIES If a power failure occurs during manual, 01-01-'01 MON timer or alarm recording, the VCR will 00:00:00 X L24 return to the recording mode when the power comes back on. The Power Failure symbol (X) will be displayed for about 1 minute on screen and the Power Loss indicator ( ) will illuminate on the fluorescent display when the power comes back on. If a power failure occurs while the VCR's power is on, the VCR will turn on by itself when the power comes back on. Displaying/clearing the power loss list Displaying the power loss list The power failure start time is logged in the VCR's Power Loss List. To view the list, please follow the steps listed below. Turn JOG to select MAINTENANCE and turn SHUTTLE to the right. Turn JOG to select POWER LOSS LIST and turn SHUTTLE to the right. · <POWER LOSS LIST> appears. · The day and present time appears on screen. Info. <MAINTENANCE> POWER LOSS LIST ALARM LIST ALL MENU INITIALISE POWER LOSS LIST CLEAR ALARM LIST CLEAR <REPEAT REC TIMES> <ELAPSED TIME> 0 0H <REAR TERMINAL> CALL OUT WRNG·TAPE END CLOCK OUT T/L REC- F MODE OUT REC REC IN SERIES <REAR TERMINAL> CALL OUT WRNG·TAPE END CLOCK OUT REC- 1 MODE OUT REC REC IN SYNC REC The day and present time appears on screen. page 20 for synchronous recording connection 14 Advanced Functions Note A point to notice The battery is fully charged if the VCR's power cord is plugged into the outlet for 40 or more hours per week. [. . . ] The type of malfunction corresponding to the indicator and countermeasures are given below. Fluorescent display Monitor TAPE END Cause The tape ends during recording. Remedy Rewind the tape or press the EJECT button. Check for loose connections. To turn off the indicator Turn off the indicator on the fluorescent display and screen by pressing the EJECT button or rewinding the tape. When a video signal is restored or the recording mode is cleared, the indicator on the fluorescent display and screen turns off. End noSIg NO SIGNAL Lack of video signal input. (the display starts flashing) CHECK Tape/deck trouble. First, check the cassette. If there seems to be nothing wrong with the cassette, try the recording operation again. [. . . ]