User manual MITSUBISHI HS-U449

[. . . ] VIDEO CASSETTE RECORDER OWNER'S GUIDE VCR POWER CHANNE EJECT L VOL UME TV POWER MUTE 1 4 7 QUICK PROGRAM 2 CM SKIP 3 6 9 INPUT 5 8 0 PLAY VCR TV REW FF REC PAUSE STOP X2 DISPLAY INDEX AUDIO /VIDEO ADJUST CANCEL ENTER VCR/TV MENU SP/EP ADJUST MODEL HS-U449 This Video Cassette Recorder is based on the VHS format. Only video cassette tapes with the mark may be used with this model. Special Features HS-U449 SMART: Program Conflict Warning VHS Hi-Fi audio record/ playback FAST: Alfa 500 Precision High Speed Mechanism with for 500x rewind/fast forward speed Rental XpressTM ­ Auto rewind, eject and power off for a fast movie return EASY: ViewPoint® Menu Operating System OTR2 Advanced One Touch Recording with delayed start time Auto Clock Set Front A/V input jacks CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. IMPORTANT: RECORDING OF COPYRIGHTED TELEVISION PROGRAMS MAY VIOLATE COPYRIGHT LAW. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION: TO PREVENT ELECTRIC SHOCK HAZARD, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. NOTE TO CATV SYSTEM INSTALLER: THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER'S ATTENTION TO SECTION 820-40 OF THE NEC WHICH PROVIDES GUIDELINES FOR PROPER GROUNDING AND, IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN SHORTCUTS To connect your VCR, go to page 4. [. . . ] Make sure the programmed recording light is back on. After a program has been recorded, the VCR memory of that program is cleared (unless you have scheduled the VCR to record the program every day or every week). If there is already a program in the VCR's memory, you will see the Recap screen when you bring up the menus for programming to record (unless you are programming with the QUICK PROGRAM). If the VCR's memory is full, Program memory is full will appear on the screen. If so, you must erase a program before you can enter a new one. If a tape runs out during timer recording, the VCR ejects the tape and the programmed recording light ( ) and the cassette light ( ) will flash. If you forget to load a tape, the programmed recording light ( ) and the cassette light ( ) will flash when you turn the VCR power off. (A tape without an erasure tab will be ejected. To correct this, load a tape with its erasure tab intact, and turn off the VCR. ) Do not overlap the recording times you enter into the VCR. If you set two programmed recording times overlap, VCR is already programmed for that time will appear on your screen. Remember that the VCR will record over the next section of tape. If you want to save a tape, remove it and instead use a different tape for a new recording. Your VCR will not record over a tape that has the erasure prevention tab removed. All rental movies have this tab removed, so they are safe from being accidentally erased. POWER REC REC VCR POWER 1 4 7 2 5 8 0 3 6 9 27 Timer Recording Auto speed programming Use auto speed programming if you want to record as much of the program as possible in standard play (SP) speed, but you want the VCR to automatically switch to extended play (EP) if there is not enough tape left. Auto speed programming is only available for one program. In the first slot, the recording speed default is AUTO. Make sure that the Tape video function matches the length of tape you are using. See Selecting and adjusting the audio and video functions on page 23. At the point where the recording mode changes from standard play (SP) to extended play (EP), some noise may be in the picture or sound when playing the tape. Program caution If your VCR is set to record, but the power is still ON within 3 minutes before timer recording starts, this screen will appear to remind you to turn off the VCR. If the VCR is still turned on 12 seconds before the start time of the recording, that timer recording will be cancelled. program caution REC in 3 min Turn off VCR TV programs that end on the day after If you want to start the recording at 11:00 PM and end it at 2:00 AM the next day, simply set the start time to 11:00 PM on the recording start day and the end time to 2:00 AM. There is no need to change the day of the week. Program skip using menus Sometimes you may want to skip one day of a timer recording but do not want to erase it. Program skip will prevent the recording, for that day only, of a program you have scheduled to record every day or every week. [. . . ] Parts used for replacement are warranted for the remainder of the original warranty period. For ninety days from the date of original purchase at retail, we will provide the labor for a warranty repair without charge at an authorized MITSUBISHI service center. To obtain warranty service, you must notify an authorized MITSUBISHI service center of any defect within the applicable warranty time period. 1 TO OBTAIN WARRANTY SERVICE, deliver your VCR to the nearest MITSUBISHI service center. [. . . ]