User manual MITSUBISHI KD12

[. . . ] Use the attached RGB cable and RS-232C cable and the shielded LAN cable with this equipment so as to keep interference within the limits of a FCC Class B device. DO NOT LOOK DIRECTLY INTO THE LENS WHEN THE PROJECTOR IS IN THE POWER ON MODE. CAUTION Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/ Data Processing Equipment, ANSI/NFPA 75. When using the projector in Europe: COMPLIANCE NOTICE This projector complies with the requirements of the EC Directive 2004/108/EC "EMC Directive" and 2006/95/EC "Low Voltage Directive". [. . . ] Select to change the SETUP mode automatically. · When 7. 5% is chosen, the brightness is decreased by the set-up cancel function for the U. S. Choose ON when connecting the projector with a device equipped with the SCART terminal that can output RGB signal. SCART terminal is used mainly in Europe. (Available only for the input signal from the COMPUTER/COMPONENT VIDEO IN-1 terminal. ) Use to select the language used in the menus. Use to reset the settings of the menu (excluding IMAGE CAPTURE, PASSWORD FUNCTION and LANGUAGE) to the factory setting values. CINEMA MODE can be adjusted only when a TV60, TV50, 480i or 576i signal is being displayed. When SCART INPUT is set to ON, nothing is output to the external monitor. When SCART INPUT is set to ON, normal computer signals aren't projected. Use a commercially available SCART-Mini D-SUB 15-pin cable when connecting this projector with an AV device equipped with the SCART terminal. Some AV devices equipped with the SCART terminal aren't compatible with this projector. EN-25 Menu operation (continued) 4. SIGNAL menu opt. SIGNAL - RESOLUTION (MEMORIZE) menu opt. SIGNAL - USER menu opt. SIGNAL A U H V SIGNAL AUTO 1024x768 0 0 0 0 RGB 100% OFF OK SIGNAL USER 75. 04 Hz 60. 02 KHz 1024 768 OK OK ? MEMORY CALL RESOLUTION (MEMORIZE ) HORIZ. Use to eliminate vertical wide stripes, if appears, viewing the projected image. The proper setting is automatically selected. Select this option when connecting the projector to high definition video equipment having R, G, and B output terminals. Select this option when connecting the projector to a DVD player or other device having Y, CB, and CR (or Y, PB, and PR) component video output terminals. Use to adjust the display area of projected image. Use to adjust the image when flagging occurs near the top of the screen. RESOLUTION (MEMORIZE ) 640-1920 VERTICAL FREQUENCY HORIZONTAL FREQUENCY HORIZ. LINES 350-1200 EXECUTE CANCEL HORIZ. TRACKING COMPUTER INPUT OK OK 0-999 0-999 0-31 0-9999 AUTO RGB YCBCR/YPBPR OVER SCAN HOLD USER CLAMP POSITION CLAMP WIDTH VERT. SYNC 100%-90% OFF / ON 1-255 1-63 AUTO / OFF Use to correct solid white or solid black in the projected image. Use to correct solid black in the projected image. Use to adjust the image when its motion doesn't run smoothly. LPF ON / OFF Use to select whether or not to enable the LPF. [. . . ] · In the REAL mode, images are black-framed when the image resolution is lower than 1400 x 1050. · This projector doesn't support 480p signals from video devices having 4 lines (R, G, B, CS*) or having 5 lines (R, G, B, H, V). * : Composite Sync Connectors SERIAL (D-SUB 9-pin) 5 9 1 COMPUTER/COMPONENT VIDEO IN-1/IN-2 (Mini D-SUB 15-pin) 5 10 6 15 11 1 Pin No. R(RED)/CR G(GREEN)/Y B(BLUE)/CB GND GND GND GND GND DDC 5V (*1) GND GND DDC Data (*1) HD/CS VD DDC Clock (*1) DVI-D (HDCP) (DVI-D 24-pin) 16 24 17 9 6 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 8 1 Pin No. TMDS DATA 2TMDS DATA 2+ TMDS DATA 2 Shield DDC Clock DDC Data TMDS DATA 1TMDS DATA 1+ TMDS DATA 1 Shield - Pin No. [. . . ]