User manual MITSUBISHI LAN CONTROL UTILITY FOR XD8100U XD8100LU WD8200U WD8200LU V3.0

[. . . ] LAN Control Utility User Manual (for XD8100U/XD8100LU/WD8200U/WD8200LU) Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Preparing to use network features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Functions and features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] (2) Select "Edit Projector Setting" from "Configuration" of the menu bar. · "EditProjectorSetting"windowisdisplayed. (3) Click [Delete]. · Theselectedprojectorisdeleted. EN-13 5. Operation of projector by remote controller Group or single unit of projector can be operated. (1) Select the projector which you like to operate from the projector list on the main screen. · Whenselectingmorethanoneprojectorsimultaneously, selectwhilepressingtheCtrlkey. (2) Click [Remote Controller] of the tool bar on the main screen or when you like to operate a certain projector, double click the projector on the projector list on the main screen. · "RemoteController"windowisdisplayed. (3) Operate the projector by selecting each operating button on the window. Command Power Input Source Button Power ON Power OFF COMPUTER 1 COMPUTER 2 VIDEO S-VIDEO HDMI *1 DVI-D *1 DIGITAL 3 NETWORK Description Turn on the power supply of the projector. Turn off the power supply of the projector. ClosetheRemoteControllerwindow. Exit *1 HDMI and DVI-D are displayed with DIGITAL 1 or DIGITAL 2 by a connected projector. <Note> · Thenextoperationcannotbeperformeduntilthepreviousoperationhasbeencompleted. · Theoperationcannotbeperformedduringre-obtaining(refreshing)theprojectorstatus. · Availableinputsourcesvarydependingonthetypeofprojectors. Youcannotselectinputsourcesthataren't supported by the projector. EN-14 5. Confirmation of projector status The status of the projector is displayed on the projector list on the main screen. Item Check No. Projector Name MAC Address IP Address Power InputSource AVMute Lamp1/2Time(Low) Description Theftdetectorsetting(ON/OFF) Projector list registration number Projector name set in the application MAC address of the projector IP address of the projector Powersupplystatusoftheprojector(ON/OFF) Inputsignaloftheprojector(COMPUTER1/COMPUTER2/VIDEO/S-VIDEO/ DIGITAL1/DIGITAL2/DIGITAL3/NETWORK) Mutestatusoftheprojector(ON/OFF) Lampilluminatingtime(HHHH:MM) In the case of the projector equipped with two lamps, illuminating time for the lamp 1 is displayed in the left side and illuminating time for the lamp 2 is displayed in the right side. The belonging group of projector Group Name · Theprojectorstatusisre-obtained(refreshed)automaticallyandperiodically, butthepresentstatuscan also be obtained by the user's instruction. When clicking [Refresh Status] of the tool bar on the main screen, Power, Input Source, AV Mute, and Lamp Time (Low) status of each projector is re-obtained. · ThestatusofInputSourceandAVMutewillnotbeobtainedunderthefollowingconditions: - when the projector is powered off - during warm-up or cool-down. · Whenclickingthestatustagoftheprojectorlist(excepttheMACaddress), thelistcanberearranged(sorted). The list can be rearranged in reversed order by pressing one more time. · Whenclicking[SelectAll]ofthetoolbar, allprojectorsintheprojectorlistbecomeselected/nonselected state. · Ifanyabnormalstateoftheprojectorisdetectedbyacquiringtheprojectorstatus, anerrormessagewillbe displayed on the error message display column at the lower part of the screen. <Note> · Thedefaultcycleoftheautomaticre-acquisitionis10minutes. Tochangethiscycle, see"3. 1. System settings. " · Whenmultipleprojectorsareconnected, itmaytaketimetoacquirethestatus. Duringacquiringthestatus, the status bar at the lower part of the main screen becomes "Getting status. . . ", and it becomes "Done" when the acquisition has been completed. EN-15 6. Creation of projector group Multiple projectors can be controlled and batched by sorting groups. Also, eachgroupcanseteachtimeofthepowersupplyON/OFFeveryday. SincethescheduleofthepowersupplyON/OFFisperformedbyeachgroup, theprojectorwhichyoulike tooperate at the same schedule should be integrated into the same group. When Power ON and Power OFF are enabled, their time settings are indicated on the schedule list. [Example] When setting the schedule for the group "group 1" to turn the power supply ON at 9:00 on Monday, turning OFF at 17:00 on the same day, ON at 8:30 on Thursday, and OFF at 17:40 on Friday. [. . . ] In this manner, up to ten rows are automatically added to the table. (3) Click [Exit] to close the window. <Note> · Onceaschedulehasbeenconfigured, itisexecutedautomaticallyeveniftheVisualPA2windowisnot displayed. · IfyousendmessagesmanuallyfromVisualPA2whenascheduleisbeingexecuted, thesemessageshave higherpriorityoverthatschedule. Inaddition, whenthesettingsofaschedulecurrentlybeingexecutedare reconfigered, the Visual PA2 window will close automatically. · Morethanoneschedulecannotbeconfiguredatthesametimeonthesameday. · TheScheduleSettingwillbeexecutedwhile"ProjectorViewGlobal+"isinoperation. [. . . ]