User manual MITSUBISHI LDT422V

[. . . ] 42" LCD Display Monitor MODEL Index Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . English-2 Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . English-3 Declaration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . English-5 Safety Precautions, Maintenance & Recommended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · For HDMI cable connection, select HDMI audio. (You can select HDMI audio only when the video input is [RGB1]. ) Signal cable (BNC x 3 to D connector) To D connector output LCD monitor (rear) BNC cable (BNC x 3 to BNC x 3) To video output DVD player (component device) BNC-RCA adaptor Audio output RCA cable (audio) DVD/HD IN (Y·Pb·Pr, Y·Cb·Cr) AUDIO IN2 (RCA) G B R DVI IN HDMI RS-232C IN VIDEO IN S-VIDEO IN2 IN3 L IN1 OUT R V H D-SUB OUT D-SUB IN RS-232C OUT VIDEO OUT DVD player (HDMI device) HDMI cable RGB1 IN (HDMI) To HDMI output English-20 P-4 Connection procedure (continued) Connecting a video device (composite video/S video device)/stereo amplifier This monitor can be connected to a stereo amplifier. Refer to the user's manual of the stereo amplifier for details. (Cables shown in the figure below are commercially available. ) · To connect a video device to the VIDEO IN connector (VIDEO IN or S-VIDEO IN) on the monitor, use a BNC cable or an S video cable. For connection to the audio input connector on the monitor, use an RCA cable (audio cable). Connect the connectors of the RCA cable (audio) correctly. For connection to the VIDEO IN connector, select [VIDEO] using the INPUT button on the monitor or the VIDEO button on the wireless remote control. For connection to the S-VIDEO IN connector, select [VIDEO<S>] using the INPUT button on the monitor or the VIDEO(S) button on the wireless remote control. · When connecting a stereo amplifier to the monitor, be sure to turn off the power of the stereo amplifier. For connection to the audio output connector on the monitor, use an RCA cable (audio). Connect the connectors of the RCA cable (audio) correctly. Be sure to turn on the monitor first, and then turn on the stereo amplifier. · The selected audio input signal is output from the AUDIO OUT connector. LCD monitor (rear) RCA cable (audio) S video cable S-VIDEO IN AUDIO IN2 LCD monitor (first monitor) G B R HDMI DVI IN RS-232C IN VIDEO IN S-VIDEO IN2 IN3 L R V H D-SUB OUT D-SUB IN RS-232C OUT VIDEO OUT IN1 OUT VIDEO IN AUDIO OUT BNC cable VIDEO OUT RCA cable (audio) To S video output To Audio output To video output BNC cable To Audio input Video device (composite video/S video device) Stereo amplifier VIDEO IN LCD monitor (second monitor) External speaker External speaker English-21 English P-5 · · Connecting the power cord to the monitor Connecting the power source The power outlet socket should be installed as near the equipment as possible and should be easily accessible. Fully insert the prongs into the power outlet socket. Loose connection may cause noise. NOTE: Please refer to "Safety Precautions, Maintenance & Recommended Use" in this manual for proper selection of the AC power cord. Clamper (Accessory) Cable holder Use the clamper to secure the cable firmly. Power cord (For EU) Power cord (For North America) English-22 How to Use Flow of How to Using U-1 Turning on all the connected devices Page 24 U-2 Selecting the video input Page 25 U-3 Controlling the external devices Page 26 RGB3 and RGB4 only U-4 Auto-setup Page 26 U-5 Selecting the picture mode Page 26 U-6 Screen adjustment Page 27 U-7 Picture adjustment Page 27 Carry out as necessary U-8 Volume control Page 28 U-9 Schedule setting Pages 28 to 29 U-10 Remote control Pages 30 to 31 English-23 English U-1 Turning on all the connected devices Power Indicator Status Power ON Power OFF Power Standby when "SCHEDULE" is enable Power Standby Diagnosis (Detecting failure) LED Green Red Red On Green Blinking Red, Green Red Blinking * See troubleshooting on page 44. Turning on external devices 1. Turn on the connected devices such as the computer and VCR. Before turning on the monitor, turn on the computer. Turning on the monitor 2. Turn on the Main Power Switch. The power indicator turns on green. The control buttons on the bottom of the monitor and the wireless remote control don't work while the Main Power Switch is off (the power indicator is off). When using them, check that the Main Power Switch is on (the power indicator is on). 3. When the power indicator glows red, press the POWER button on the monitor. The power indicator turns green. Main Power Switch Power Management Function This function reduces the power consumption of the monitor when the keyboard or the mouse is not used for a fixed period even though the power of the monitor is on. While this function is working, the screen becomes dark and the power indicator glows green and red. This function is available only when a computer equipped with the VESA-approved DPM Power Management function is connected to the monitor. [. . . ] · Use the OSD Image Adjust controls to focus and adjust the display by increasing or decreasing the fine adjustment. When the display mode is changed, the OSD Image Adjust settings may need to be re-adjusted. · Check the monitor and your display card with respect to the compatibility and recommended signal timings. · If the displayed text is garbled, change the video mode to the non-interlace mode and use 60 Hz refresh rate. [. . . ]