User manual MITSUBISHI NM-VS100

[. . . ] This unit complies with the requirements of the EC Directive 2004/108/EC, "EMC Directive". The requirements for the susceptibility according to EN 55024 and the requirements for interference according to EN 55022 are observed for the operation on residential areas, business, light industrial premises and in small scale enterprises, inside as well as outside of the building. All places of operation are characterized by their connection to the public low voltage power supply system. Warning This is class A product. In a domestic environment this product may cause radio Interference in which case the user may be required to take adequate measures. i Note: This symbol mark is for EU countries only. [. . . ] Setting methods for Image Appearance and MPEG4 Video Stream takes the same process as the image settings of each channel. Sequence Setting It is an image setting for Sequence Mode which shows 4 input images with an automatic sequential switching. The setting method for Image Appearance and MPEG4 Video Stream is the same as the image setting of each channel. - 10 - 3. 3. 2 Live View Setting Source Setting Set the channel by web browser-based connection and the allocated channel to BNC Out. Default Live View Set the channel by web browser-based connection. You can select one among the 4: Channel1, Channel2, Channel3, Channel4, and Quad Stream. The chosen screen is seen on the control screen as a basic one. Screen modification is possible even during the control operation. BNC Out One screen out of the 4 input images and Quad Stream can be allocated by BNC Out. The allocated screen can be seen through general CRT monitor. - 11 - Sequence Setting Automatic screen switching setting can be seen with the control screen and BNC Out, and either watching one of the two or the two at a time is possible. You can select, among the 4 channels and Quad screen, the screen that will be included in switching list, for each of which you can set delay time separately. Sequence Mode Setting Enable Allow checking at time of an automatic screen switching function in operation. Use sequence mode in Live View Make it possible to see the automatic screen switching on the control screen. Use sequence mode in BNC Allow the automatic screen switching to be seen on BNS Out screen. Use sequence mode in Live View and BNC Out Allow the automatic screen switching to be seen on the control screen and BNS Out screen. Channel1~4, Quad Stream Each of the 4 channels and Quad screen can be selected to be included on the switching list to set up the delay time. - 12 - 3. 3. 3 Audio Setting Basic Setting Users can use a microphone and speaker by using the audio function. Audio Setting Compression type Users can increase a transmission rate or enhance a tone quality by selecting an audio compression mode. The PCM 16-bit implements the best tone quality, while the PCM 8-bit corresponds to that of radio sound. Sample rate If a sample rate is low, the tone quality will go down but the transmission rate will go up. If a sample rate is high, the tone quality will be better, but the transmission rate will drop. Please, adjust its rate in accordance with a network status or purposes. Audio Input Source Users can select either MIC input or LINE input, but cannot use both at once. Input Volume Users can control the input volume by adjusting the microphone volume. Audio Output Output Volume Users can control the output volume of the speaker connected to the Video Server. - 13 - 3. 3. 4 Alarm Setting This function enables users to conduct the alarm input/output setting and event setting. Motion Setup Motion information is processed by splitting the screen into 64 areas. Each area can be selected by clicking with the mouse, and the selected area is highlighted. [. . . ] Log & Report Users can check the system log and server report. Logs Reports Users can check the log for Video Server operation by clicking the < Logs >. Users can check a server report by clicking the < Server Report >. Users can check a parameter by clicking the < Parameter List >. - 30 - Program Information The following website will provide the support information for the Video Server system information and operation. 3. 4 Help The Help information window will be provided as a popup window so that users can open and read it without a need for log-in. It will offer a description on setting and Help page by which users can manipulate the Video Server without a reference to the manual. - 31 - 4. Appendix 4. 1 Troubleshooting If problems occur, verify the installation of the camera with the instructions in this manual and with other operating equipment. Isolate the problem to the specific piece of equipment in the system and refer to the equipment manual for further information. PROBLEM AREA TO CHECK Verify that power is connected to all pieces of equipment in the system. [. . . ]