User manual MITSUBISHI PEFY-P06

[. . . ] English-6 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . English-7 Parts Name and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . English-8 Buttons, Switch, and Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . English-8 Connectors and Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] By repeating the connection in the similar way, you can connect monitors in a daisy chain configuration. Computer (RS-232C connection) RS-232C cable RS-232C RS-232C OUT RS-232C IN RS-232C OUT RS-232C IN Left side of LCD monitor (first monitor) RS-232C cable Left side of LCD monitor (second monitor) NOTE: When only the 25-pin serial port is equipped as the serial communication port on the computer, a conversion adapter (commercially available) is necessary for the connection. English-27 English To control this monitor from a computer via a communication, connect this monitor and the computer using an RS-232C cable (commercially available). P-7 Connecting LAN Monitor connection using LAN Carry out as necessary As shown in the illustration below, you can connect this monitor and a computer in network through a LAN hub. Connect the monitor and the LAN hub using a straight type LAN cable (commercially available). How to connect · · · · Turn off the main power switch of the computer and this monitor. If you make a connection while the power is on, it causes a failure of the devices. Connect the computer and the LAN hub using a straight type LAN cable (commercially available). Connect this monitor and the LAN hub using a straight type LAN cable (commercially available). When you connect two or more monitors, you can connect the monitor and the LAN hub using a straight type LAN cable (commercially available) as described above. Computer (LAN connection) Left side of LCD monitor LAN LAN cable LAN hub LAN hub LAN cable LAN hub LAN CAUTION: Do not connect the CAT5 IN or the CAT5 OUT connector to the LAN connector. If connected, both of the connectors may fail. NOTE: · When you use a cross type LAN cable (commercially available), you can connect the monitor and the computer one-to-one without using a LAN hub, however, the computer may not be supported. It is recommended to check the operation in advance. · The image transfer function via the LAN isn't supported. The control buttons on the rear of the monitor and the wireless remote control don't work while the Main Power Switch is off (the power indicator is off). When using them, check that the Main Power Switch is on (the power indicator is on). Power button Wireless remote control Main Power Switch English-32 U-1 Turning on all the connected devices (continued) Power Management Function This function reduces the power consumption of the monitor when the keyboard or the mouse is not used for a fixed period even though the power of the monitor is on. While this function is working, the screen becomes dark and the power indicator glows green and red. This function is available only when a computer equipped with the VESA-approved DPM Power Management function is connected to the monitor. When the power saver in the OSD menu is turned ON, the power management function works. RGB: When the sync signal of computer input (RGB1, 2, 3, 4, OPTION (CAT5), or RGB6) is terminated, the monitor will be in the sleep mode in several seconds. VIDEO: When the sync signal of video input (DVD/HD, VIDEO<S>, or VIDEO) is terminated, the monitor will be in the sleep mode in approximately 10 minutes. [Description] DPM: Acronym for Display Power Management NOTE: · · The default power management settings (power savers) for RGB and VIDEO are ON. When an OPS-compliant module is in the option slot, the monitor doesn't enter the sleep mode even when POWER SAVE in the CONFIGURATION1 menu is set to ON. Even when other video input is selected, the monitor doesn't enter the sleep mode. Power Indicator Status Power ON Power OFF Power Standby when "SCHEDULE" is enable Sleep mode Diagnosis (Detecting failure) Green Red Red On Green Blinking Red, Green Red Blinking * See troubleshooting on page 62. LED English-33 English U-2 Selecting the video input You can select the desired video input using the wireless remote control or the INPUT button on the monitor. Select using the INPUT buttons on the wireless remote control. You can select the desired video input by pressing the corresponding INPUT button on the wireless remote control. Selectable video inputs are [RGB1] (HDMI), [RGB2] (DVI-D), [RGB3] (D-SUB), [RGB4] (BNC), [OPTION]*, [RGB6] (DISPLAY PORT), [DVD/HD] (YPbPr), [VIDEO<S>], and [VIDEO]. [. . . ] NOTE: As with all display devices, MITSUBISHI ELECTRIC recommends displaying moving images and using a moving screen saver at regular intervals whenever the screen is idle or turning off the monitor when not in use. Image is unstable, unfocused or swimming is apparent · Signal cable should be securely attached to the computer. · Use the OSD Image Adjust controls to focus and adjust the display by increasing or decreasing the fine adjustment. When the display mode is changed, the OSD Image Adjust settings may need to be re-adjusted. [. . . ]