User manual MITSUBISHI XD70U

[. . . ] DATA PROJECTOR MODEL XD70U User Manual IMPORTANT * DLPTM (Digital Light Processing) and DMD (Digital Micromirror Device) are registered trademarks of Texas Instruments Incorporated (U. S. A. ). * DMD is an ultra-precise part developed by Texas Instruments (U. S. A. ) which takes the place of liquid crystal (in the projector). * VGA and XGA are trademarks or registered trademarks of International Business Machines Corporation (U. S. A. ). * S-VGA is a registered trademark of Video Electronics Standards Association. [. . . ] · Press the CANCEL button to close the timer display. The timer setting will return to "Off". Moving the Position of the Timer Display The SELECT buttons on the remote control permit movement within the movable range of the timer display. Movable Range of the Timer Display Note: * The timer display will be closed while the menu or the quick menu is displayed, and while a message is displayed; however, the timer will still be operating at such times. Also, the timer will not be displayed unless a signal is being input. * While the presentation timer is being displayed, screen movement will not be possible in the zoom mode. E-30 General Operation Using the Laser Pointer The remote control unit's laser pointer can be used to point to the section currently being explained, making presentations more effective. CAUTION Do not look at the laser pointer's light source. Pointing the laser beam at the eyes could lead to reduced vision or vision impairment. · Never look at the laser pointer's light source. · Do not point the laser beam at people. · Do not let children use the laser pointer. This label is located on the side of the remote control. Operation The red laser beam is emitted from the tip of the remote control unit while the LASER button is pressed in. Point the remote control unit's transmitter in the direction you want to indicate. The laser beam turns off when you release your finger from the LASER button. S TA N D B Y R G B M E N U V ID E O A U TO Q U IC LA S E R E N TE R FR EE ZE / K L LIC E -C C R AN C Q K M U TE TIM 1 V O L E R 3 2 4 ZO O M LASER Note: If a button on the remote control unit is held in continuously for approximately 30 seconds, signal transfer will be suspended. To resume transferring signals, press the button again. Also, to use the jog button after signal transfer has been suspended, first press any other button, then press the jog button. E-31 General Operation Performing Mouse Operations on the Computer with the Remote Control Unit When a computer and the projector are connected, mouse operations can be performed on the computer using the projector's remote control unit. When projecting images from the computer, the projector can be operated and mouse operations on the computer performed with the same remote control unit, making for efficient presentations. Connecting the computer and projector Use the USB cable included with the projector to connect the computer's USB (type A) connector to the projector's MOUSE connector. Note: * Be sure to plug the cable in securely. * Depending on the type of connection, the computer's operating system, etc. , it may be necessary to change settings or restart the computer after making the connections. USB connector USB cable (mini B to A type) (Supplied item) Functions of the mouse function buttons When operating, point the remote control unit's transmitter towards the remote control sensor on the projector. L-CLICK button (on back) Press this to perform the left-click operation. LASER VIDEO AUTO STANDBY RGB MENU QUICK JOG buttons These move the computer's pointer in the corresponding direction. R-CLICK button Press this to perform the right-click operation. Q ENTER R-CLICK/ CANCEL FREEZE MUTE TIMER 1 VOL 2 ZOOM INFORMATION The R-CLICK/CANCEL button is used for both the projector and mouse function. When the R-CLICK/CANCEL button is pressed while a menu is open, the menu is closed. 3 4 Note: Connections with USB Cables * For PC/AT compatible computers, this function cannot be used with operating systems other than Windows 98SE, Me, 2000 and XP. For Macintosh computers, this function cannot be used with operating systems other than OS 9 and later. * When the cable is disconnected and then reconnected to the USB port of the personal computer or the MOUSE connector of the projector, allow at least 5 seconds before reconnecting. [. . . ] Doing so could shorten the life of the lamp. · If lamp has reached the end of its usable life, the lamp bulb may shatter. When this happens, an explosive sound can be heard and pieces of glass may be scattered in the lamp cartridge. Do not touch them as the pieces of glass may cause injury. [. . . ]