User manual MOFFAT MG35W

[. . . ] Do not attempt to modify the hob in any way. Service This hob should only be repaired or serviced by an authorised Service Engineer and only genuine approved spare parts should be used. Environmental Information After installation, please dispose of the packaging with due regard to safety and the environment. When disposing of an old appliance, make it unusable, by cutting off the cable. The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. [. . . ] Check the burner cap and crown have been replaced correctly, e. g. If after all these checks, your hob still does not operate correctly, contact your local Service Force Centre. Please note that it will be necessary to provide proof of purchase for any in-guarantee service calls. In-guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown. 5 Service and Spare Parts In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local Service Force Centre by telephoning: Customer Care Department For general enquiries concerning your Moffat appliance or for further information on Moffat products, please contact our Customer Care Department by letter or telephone at the address below. 0870 5 929929 Your telephone call will be automatically routed to the Service Force Centre covering your post code area. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www. serviceforce. co. uk Before calling out an engineer, please ensure you have read the details under the heading "Something Not Working. " When you contact the Service Force Centre you will need to give the following details: 1. Clear and concise details of the fault 4. The model and serial number of the appliance (found on the rating plate) 5. The purchase date Customer Care Department Moffat 55-77 High Street Slough Berkshire SL1 1DZ Tel : 08705 950950 * calls to this number may be recorded for training purposes. Guarantee Conditions Moffat Guarantee conditions We, Moffat, undertake that if, within 24 months of the date of the purchase, this Moffat appliance or any part thereof is proved to be defective by any reason only of faulty workmanship or materials, we will, at our option, repair or replace the same FREE OF ANY CHARGE for labour, materials or carriage on condition that: * The appliance has been correctly installed and used only on the gas and electricity supply stated on the rating plate. * The appliance has been used for normal domestic purpose only, and in accordance with the manufacturer's instructions. * The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not authorised by us. * All service work under this guarantee must be undertaken by a Moffat Service Centre. However, if the room has a door which opens directly to the outside no air vent is required even if the volume is between 5 m3 and 11 m3. If there are other fuel burning appliances in the same room, B. S. Ensure that the main connection pipe does not exert any strain on the hob. FO 0814 FO 0264 A) End of shaft with nut B) Washer C) Elbow It is important to install the elbow correctly, with the shoulder on the end of the thread, fitted to the hob connecting pipe. Failure to ensure the correct assembly will cause leakage of gas. Cut Out Size The dimensions of the cut-out are given in the diagram. Rectangular cut-out size for hob FO 2038 9 Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry out the electrical connection to the hob as shown in diagrams 1 and 2. Dimensions are given in mm. Building over a kitchen unit with door Proper arrangements must be taken in designing the furniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated. The recommended solution is shown in diagram 3. The panel fitted under the hob ("a") should be easily removable to allow easy access if technical assistance is needed. The space behind the kitchen unit ("b") can be used for connections. 1 ON/OFF SWITCH ON/OFF SWITCH 2 3 FLEX OUTLET FLEX OUTLET FO 2563 FO 2564 FO 2044 Fitting the Hob into the worktop Carry out the building in of the hob as follows: · put the seals supplied with the hob, on the edges of the cut out: place them exactly on the front and rear edge and at 50 mm. from the side edges, as shown in the diagram, taking care that the seals meet without overlapping; · place the hob in the cut out, taking care that it is centred; · fix the hob with the relevant fixing clamps and screws, as shown in the diagram. When the screws have been tightened, the excess seal can be removed. [. . . ] Rectify any fault. Isolate appliance and carry out: B: Insulation check. Rectify any fault including replacing fuses as necessary. A. EARTH CONTINUITY CHECK - Appliance must be electrically disconnected - meter set on (Ohms) x 1 scale and adjust zero if necessary. a) Test leads from any appliance earth point to earth pin on plug. [. . . ]