User manual MOOG 201780-XXX REV B

[. . . ] Mini4 Data Mux User's Manual (201780-xxx) And Troubleshooting Guide June 7, 2010 Rev B Moog Components Group 750 West Sproul Road, Springfield, PA 19064 E-Mail: URL: Tel: 610-328-4000 Fax: Moog Components Group Mini4 Data Mux, Rev B (201780-xxx) June 7, 2010 TABLE OF CONTENTS Mini4 Data Mux Board P/N ­ 201780-xxx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Mini4 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Mini4 Data Mux Board Dash (-) Number Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Mini4 Data Mux Board Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Located on the upper right of the board. Green is , , ON when serial data is being received into the board on channel 1, Red is , , ON when serial data is being transmitted out of the board on channel 1. D18 (Green) D22 (Green) D24 (Red/Green) D26 (Red/Green) D30 (Red/Green) D31 (Red/Green) D32 (Red/Green) D34 (Red/Green) D35 (Red/Green) D36 (Red/Green) NOTE: the fuses are the positive temperature coefficient self-resetting type and do not require replacement Page 5 of 14 Moog Components Group Mini4 Data Mux, Rev B (201780-xxx) June 7, 2010 FUSES: F1, a 1. 5A PTC fuse protects the isolated power supply for data channels 8 & 7. F2, a 2. 6A PTC fuse protects the +5VDC input to the board. F3, a 1. 5A PTC fuse protects the isolated power supply for data channels 6 & 5. F4, a 1. 5A PTC fuse protects the isolated power supply for data channels 4 & 3. F5, a 1. 5A PTC fuse protects and selects +5VDC for the daughterboard. Note: this fuse is replaced with a 0 ohm resistor, typically. F6, a 1. 5A PTC fuse protects and selects +3. 3VDC for the daughterboard. Note: this fuse is not placed, typically. F7, a 1. 5A PTC fuse protects the isolated power supply for data channels 2 & 1. F8, a 1. 5A PTC fuse protects and selects +5VDC for the daughterboard Note: this fuse is not placed, typically. SWITCHES: There are no switches on the Data Mux board. CONNECTORS: The connectors on the Data Mux board are as follows: J2 Daughterboard Connector VDC Supply RXD_DB1 GND RXC_DB RCV LINK RXD_DB2 1 3 5 7 9 11 o o o o o o o o o o o o 2 4 6 8 10 12 VDC Supply TXD_DB1 GND TXC_DB Future TXD_DB2 J3 Power /Diagnostics RT+ GND GND +5V +5V 1 3 5 7 9 o o o o o o o o o o 2 4 6 8 10 RTGND GND +5V +5V J5 +5DC Power entry Page 6 of 14 Moog Components Group Mini4 Data Mux, Rev B (201780-xxx) June 7, 2010 J6 Serial Data (RS-232) R1 GND_ISO_A (RS-232) R2 (RS-232) R3 GND_ISO_B (RS-232) R4 (RS-485/422) R5+ (RS-485/422) R5GND_ISO_C (RS-485/422) R6+ (RS-485/422) R6(RS-485/422) R7+ (RS-485/422) R7GND_ISO_D (RS-485/422) R8+ (RS-485/422) R8No Connect 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 T1 (RS-232) GND_ISO_A T2 (RS-232) T3 (RS-232) GND_ISO_B T4 (RS-232) T5+ (RS-485/422) T5- (RS-485/422) GND_ISO_C T6+ (RS-485/422) T6- (RS-485/422) T7+ (RS-485/422) T7- (RS-485/422) GND_ISO_D T8+ (RS-485/422) T8- (RS-485/422) No Connect NOTE: J6 header is located at the center left side of the board. Pin 1 is the bottom right pin ­ as identified by a square pad. J6 ­ Board header: Amp/Tyco 1-103167-4 Mating ribbon connector: Amp/Tyco 3414-6000 Mating crimp connector: Amp/Tyco 3-87631-0 or 2-87631-9 Mating Crimp pins: Amp/Tyco 5-102095-4 J7 Led Status GND RLINK_LED FIBER_LED VID1_LED VID3_LED R1_LED R2_LED R3_LED R4_LED R5_LED R6_LED RDIAG_LED 1 3 5 7 9 11 13 15 17 19 21 21 o o o o o o o o o o o o o o o o o o o o o o o o 2 4 6 8 10 12 14 16 18 20 22 22 PTC FUSE TLINK_LED FUTURE_LED VID2_LED VID4_LED T1_LED T2_LED T3_LED T4_LED T5_LED T6_LED TDIAG_LED NOTE: J7 header is located at the bottom center side of the board. Pin 1 is the upper right pin ­ as identified by a square pad. NOTE: J7 header is to be with a PRIZM display board only. Contact PRIZM, if details are required. Page 7 of 14 Moog Components Group Mini4 Data Mux, Rev B (201780-xxx) June 7, 2010 J8 ISP Header +3. 3V TCK N/C GND 1 3 5 7 o o o o o o o o 2 4 6 8 TMS TDI TDO NOTE: J8 to be used only by PRIZM. channels 1 & 2 share a common isolated power as do channels 3 & 4). There are no baud rate jumpers to select for RS-232 operation. The channels are simply time sampled at 12. 5 mega samples per second (Msps). The maximum RS-232 data rate is governed by the slew rate limiting on the RS-232 driver chips themselves. 4. 2. 2 Mini4 RS-485/RS-422 Data Channel Selection and Operation The 4 RS-485/RS-422 channels can have several possible configurations. The configurations are selected by placing jumper shunts on several jumper posts. [. . . ] If the LEDs operate on that channel, replace the Mini4 board with a spare board or use the working channels only. If one or more RS-422 data channel is out or has errors: Run RS-422 data into appropriate pins of connector J6. The RS-422 data can be input into either the remote vehicle or surface Mini4 board. On the other end of the link, short the TX3+ pin to the RX3+ pin and the TX3- to RX3- pins of connector J6 of the Mini4 RS-422 channel being tested. [. . . ]