User manual MOOG PRODIGY SERVICE MANUAL

[. . . ] As a motherboard, the PRODIGY provides four completely independent and "switchless" 10/100/1000 Mbps Ethernet links and can be stacked with standard 907 expansion cards to add other signal types, such as serial channels (RS-232/485/422), hydrophones, responder triggers, CANBus and various analog and digital sonars. [. . . ] GigE Vision), the low latency PRODIGY is an exceptional core solution for current and future applications. As a standalone card, PRODIGY replaces four separate Ethernet media converters with a single board and a single fiber link. This significantly reduces size and cost compared to standard media converter solutions, which typically require 2-4 stacked cards plus four transceivers, eight fibers and an optical coupler for the same Ethernet capability. Power (electrical), Optical Link, Optical Fault, PHY Rx/Tx Activity, Port Rate, Port Error Available through 907-DIAG-E card at console < 25 us (not including fiber) Latency (Remote + Console) Options Optical Optical Fiber Baud Rate Format Wavelengths Flux Budget Options Standalone version; support for jumbo frames. 1 or 2 singlemode (9/125 um) 625 - 3125 Mbaud AME-EP (Moog proprietary) 1310/1550 nm standard (CWDM optional) 20 dB min. standard (others available) CWDM wavelengths for combining multiple 907 cards on one singlemode fiber; bidirectional transceivers; extended temperature; multimode fiber +5 VDC +/-10%, regulated input required 1. 5 A typical (2 A max. ), all ports active 7. 5 W typical (10 W max. ), all ports active Overvoltage and reverse polarity Time delay fuse (3 A) Stacking Spacers 0. 72 inch standoffs required when stacking Stacking Pins Connectors Optical Data (Ethernet) Power Stacking Header Environmental Temperature Humidity Shock Vibration Options -10 to +60 °C (ambient, operational) -40 to +85 °C (ambient, storage) 85% RH, non-condensing 30 g, 11 ms half-sine, six directions +/- 2 mm (5-25 Hz), 5 g (25-1000 Hz) 6000 psi pressure tolerant version; extended temperature; stress screened or qualified units Dual LC (SFP) 4 x RJ-45 2-pin Molex, 0. 156 inch pin spacing PC/104 (for stacking 907 cards only) Short pins on PC/104 for standalone options Long pins on PC/104 for CWDM options (standard) Electrical Power Supply Current Draw Power Used Voltage Protection Current Protection PRODIGY Dimensions Dimensions in inches [mm] Specifications and information are subject to change without prior notice. [. . . ] standard (others available) CWDM wavelengths for combining multiple 907 cards on one singlemode fiber; bidirectional transceivers; extended temperature; multimode fiber +5 VDC +/-10%, regulated input required 1. 5 A typical (2 A max. ), all ports active 7. 5 W typical (10 W max. ), all ports active Overvoltage and reverse polarity Time delay fuse (3 A) Stacking Spacers 0. 72 inch standoffs required when stacking Stacking Pins Connectors Optical Data (Ethernet) Power Stacking Header Environmental Temperature Humidity Shock Vibration Options -10 to +60 °C (ambient, operational) -40 to +85 °C (ambient, storage) 85% RH, non-condensing 30 g, 11 ms half-sine, six directions +/- 2 mm (5-25 Hz), 5 g (25-1000 Hz) 6000 psi pressure tolerant version; extended temperature; stress screened or qualified units Dual LC (SFP) 4 x RJ-45 2-pin Molex, 0. 156 inch pin spacing PC/104 (for stacking 907 cards only) Short pins on PC/104 for standalone options Long pins on PC/104 for CWDM options (standard) Electrical Power Supply Current Draw Power Used Voltage Protection Current Protection PRODIGY Dimensions Dimensions in inches [mm] Specifications and information are subject to change without prior notice. [. . . ]