User manual MORPHY RICHARDS 40692 SEMI-ELECTRONIC IRON

[. . . ] Never allow the mains lead to over hang the work surface. The socket should always be off before plugging or unplugging from the socket. Never yank the cord to disconnect from the socket, instead, grasp the plug and pull to disconnect. Do not allow the cord to touch hot surfaces. [. . . ] Never fill directly under the tap. fl Ê 400 350 300 · , 2 BEFORE USE Sort out the items to be ironed according to the type of fabric. This will minimise the frequency of temperature adjustment for different garments. Note: The steam facility should only be used on garments which are suitable for ironing at the 3 dot and MAX setting. Textiles and clothes are supposed to carry ironing instructions. If they don't, you should follow the fabric guide on page 3, but be sure to test the temperature by ironing the hem of the garment or similar area first. If you adjust the temperature selection button  down from a hot setting to a cooler setting, wait until the iron temperature has stabilised before you continue ironing. Delicate fabrics such as silk, wool, velour, etc, are best ironed with an ironing cloth to prevent shine marks. COMPONENTS OF YOUR IRON / Shot of steam button ¤ Spray button < Variable steam switch > Filling hole with cap fi Spray nozzle fl Soleplate Self-clean button · Temperature console , Water tank (illuminated on some models) , , Life long anti-scale lens (certain models only) Auto shut-off indicator  Temperature selection button Ê Filling beaker A 4 UK Helpline 0844 871 0953 Replacement Parts 0844 873 0719 Ireland Helpline 1800 409 119 RN40692MUK Rev3:RN40692 MUK Rev 3 01/12/2009 11:52 Page 5 Temperature control B · · · · Default setting + 3 dot (cotton). To increase the temperature, press the arrow . To decrease the temperature, press the arrow . The temperature console · will flash to indicate that the iron has not yet reached the correct temperature. Once the correct temperature has been reached, the light will stop flashing and there will be one `beep' to signal that the iron is now ready for use. B Increase temperature Decrease temperature · FEATURES OF YOUR IRON Dry ironing You can use your iron as a dry iron only. Make sure the variable steam control < is set to the `0' symbol. Any temperature setting may be used depending on the garment. The spray feature may be used, providing there is water in the tank (see filling section). You do not need to put any water in the tank when dry ironing only. The steam output can be varied from low to high by moving the variable steam control D. The steam facility should only be used on garments which are suitable for ironing at the 3 dot and MAX setting. C Shot of steam E Press the shot of steam button / to obtain a burst of extra steam for ironing out creases in heavy material such as denim etc. The shot of steam can be used whilst dry ironing, providing there is water in the tank, and the temperature control is set within the steam range. Do not use the shot of steam at temperatures below the steam range shown on the control dial. Note: For optimum steam quality, do not operate the shot more than three times in succession. D Steam off Spray C Press the spray button ¤ and aim the spray of water at stubborn creases. You can do this whilst dry ironing, providing there is water in the tank. When using the water spray, it may be necessary to push the button a few times to get the spray pump primed. `MAX' steam Variable steam D Fill the iron with water, as described in `Filling' on page 4, and insert the plug into the electrical socket. E For details of other Morphy Richards products, please see our website: 5 RN40692MUK Rev3:RN40692 MUK Rev 3 01/12/2009 11:52 Page 6 F Vertical steam F Hold the iron in a vertical position between 1cm and 2cm away from the item F. [. . . ] Please quote the following information if the product develops a fault. These numbers can be found on the base of the product. All Morphy Richards products are individually tested before leaving the factory. In the unlikely event of any appliance proving to be faulty within 28 days of purchase, it should be returned to the place of purchase for it to be replaced. EXCLUSIONS Morphy Richards shall not be liable to replace or repair the goods under the terms of the guarantee where: 1 The fault has been caused or is attributable to accidental use, misuse, negligent use or used contrary to the manufacturer's recommendations or where the fault has been caused by power surges or damage caused in transit. [. . . ]