User manual MORPHY RICHARDS CORDLESS HAND BLENDER REV 1

[. . . ] 48965 Rev 1 13/4/04 3:47 PM Page 1 Cordless hand blender Please read and keep these instructions getting the best from your new cordless hand blender. . . Battery · Ensure the battery is fully charged before using the product. The battery is not covered by the guarantee. Safety · The blade is very sharp, handle with care, do not touch the blade or hold the leg at the blade end when fitting to the body. · The hand blender is designed for intermittent use. Do not use non-stop for more than 1 minute at a time. [. . . ] WARNING: Never use your appliance in a hot saucepan transfer to a bowl, allow to cool before blending. IMPORTANT: Your hand blender is designed for intermittent use only. Do not use non-stop for more than 1 minute. Allow to cool down for a minimum of 5 minutes before further use. To disassemble hand blender 1 To remove the blender leg, hold the blender in a position so that you cannot press the operating button. Grip shaft of blender leg, press the release button and pull apart. D WARNING: When the blender is not in use, fit the blade cover to the leg for safety. D C E 5 48965 Rev 1 13/4/04 3:47 PM Page 6 Hints for blending · The blender is perfectly suited for preparing dips, sauces, soups, mayonnaise, milkshakes and baby food. The blender can be used to purée cooked vegetables, tinned tomatoes and any soft or pre-cooked food etc. It is ideal to turn a cooked broth or stew into a smooth soup and to prepare baby food. You may need to add a little water to cooked vegetables when blending to encourage a puree to form. For milkshakes, cut soft fruit or bananas in 1. 5cm cube size pieces for easy blending, add milk and icecream a little at a time during blending. If food has been cooked in a saucepan transfer to a cooler bowl, this will protect the leg from heat distortion. For smaller quantities use the measuring beaker provided. Blending results will be better in the beaker provided as this allows control of the food being blended. Battery removal and disposal To remove the Ni-Cd battery for replacement or disposal. 1 Remove the 2 screws from the end of the battery cap, using a small phillips screwdriver and lift off the cap. G 2 Remove the connector from the end of the battery and pull out the battery. H · Replace with an approved battery pack, contact Morphy Richards replacement parts 0870 167 6643. 3 Replace the battery, (terminal to be in position shown) connect the terminal, replace battery cover ensuring it is correctly located and replace the 2 screws. IMPORTANT: The battery must be removed before the product is disposed of. The battery is to be disposed of safely, it must not be incinerated or composted. Contact your local authority for advice on disposal. · · · · Blender rest position Whilst not blending temporarily, lay the blender down on the work top as shown. F G F H battery terminal in lower left hand corner 6 48965 Rev 1 13/4/04 3:47 PM Page 7 Wall mounting The charging stand can be wall mounted or free standing. To wall mount find a suitable position on the wall away from concealed pipes and electricity cables. [. . . ] 3 Clean the blender body and base unit with a damp cloth and dry thoroughly. 10 48965 Rev 1 13/4/04 3:47 PM Page 11 Helpline If you have any difficulty with your appliance, do not hesitate to call us. We're more likely able to help than the store from where you bought it. Please have the following information ready to enable our staff to deal with your query quickly: · Name of the product · Model number as shown on the underside of the appliance. 11 48965 Rev 1 13/4/04 3:47 PM Page 12 Your two year guarantee It is important to retain the retailers receipt as proof of purchase. Staple your receipt to this back cover for future reference. [. . . ]