User manual MORPHY RICHARDS ELITE STEAM GENERATOR REV 1

[. . . ] 5 Morphy Richards are not liable to carry out any type of servicing work, under the guarantee. 6 Plastic filters for all Morphy Richards kettles and coffee makers are not covered by the guarantee. This guarantee does not confer any rights other than those expressly set out above and does not cover any claims for consequential loss or damage. This guarantee is offered as an additional benefit and does not affect your statutory rights as a consumer. [. . . ] · If you drop or severely knock your steam generator this could cause internal damage even if the outside appears alright. Have it checked by a qualified electrician. · The temperature of accessible surfaces may be high when the appliance is operating. Electrical requirements Check that the voltage on the rating plate of your appliance corresponds with your house electricity supply which must be A. C. If the socket outlets in your home are not suitable for the plug supplied with this appliance the plug should be removed and the appropriate one fitted. WARNING : The plug removed from the mains lead, if severed, must be destroyed as a plug with a bared flexible cord is hazardous if engaged into a live socket outlet. Should the fuse in the 13 amp plug require changing a 13 amp BS1362 fuse must be fitted. WARNING: THIS APPLIANCE MUST BE EARTHED. Instructions for use Temperature guide Heat setting markings on the adjustable control dial of all Morphy Richards irons match those of the International Textile Care Labelling Code. Symbol (120°C Max) Cool Control knob positions Fabric Do not iron at all Nylon, Acetates e. g. Acrilan Courtelle, Orlon Triacetates, e. g. Tricel/Polyester Iron on wrong side if moisture required use damp cloth (Not Acetate) Wool, Polyester mixtures e. g. Polyester/Cotton Cotton, Linen Rayon, Rayon mixtures, e. g. Rayon/Linen Fabrics requiring this setting usually require steam pressing for heavy cotton, denim etc. (160°C Max) Warm (210°C Max) Hot Ironing Steaming 3 St gen rn42277M rev 1 10/4/03 10:05 PM Page 5 Components of your iron / fi Location Locate the steam generator horizontally on the iron rest plate of your ironing board (if large enough) or on a heat resistant stand at the same height of your ironing board or below it. Always ensure the generator is on a firm surface when ironing. ¤ > Before use fl < · Remove any protective sticker from the soleplate and the cabinet, if any. When ironing with the steam facility at the 1 dot setting, the steam output should be set at the lower end of the steam range. Textiles and clothes are supposed to carry ironing instructions. If they don't you should follow the fabric guide on page 3, but be sure to test the temperature by ironing the hem of the garment or similar area first. If you turn the control dial down from a hot setting to a cooler setting, wait until the iron temperature has stabilised before you continue ironing. , , ,  Filling Iron unit / Steam button ¤ Temperature control dial < Sole plate > Temperature indicator light fi Supply cord from base unit Base unit fl Anti-scale cartridge Water tank · Power cord , Power switch , , -Standby mode indicator (red) -Power indicator (green) -Sleep mode indicator (green/red) Replace anti-scale medium indicator  Steam level indicators 1 Place the steam generator on a stable ironing board or table, with the iron resting on its stand. 2 Remove the detachable water tank by sliding outwards A. A 3 Remove the anti-scale cartridge by pulling upwards. B B 4 St gen rn42277M rev 1 10/4/03 10:05 PM Page 6 4 Fill the tank upto the `fill to here' line with clean tap water. Never use battery topping up fluid or water containing any substances like starch or sugar, or defrosted water from a refridgerator. 5 Re-install the anti-scale cartridge and replace the water tank on the base unit. [. . . ] Always follow the manufacturers instructions. To clean off melted man-made fibres set the iron at 3 dot position and pass it over a clean piece of cotton which will draw the deposit off the surface. To clean the exterior Allow the steam generator to cool and wipe over with a damp cloth and mild detergent, then wipe with a dry cloth. H Emptying and storing When you have finished ironing, unplug your iron. 1 Slide out the water tank and remove the anti-scale cartridge I. [. . . ]