User manual MORPHY RICHARDS IB40550

[. . . ] Ion 441375253 Rev 2 10/12/03 11:43 AM Page 1 Your two year guarantee It is important to retain the retailers receipt as proof of purchase. Staple your receipt to this back cover for future reference. Please quote the following information if the product develops a fault. These numbers can be found on the base of the product. [. . . ] (Test the inside of the hem of the garment). · When ironing is complete, remove the plug from the socket, empty any remaining water from the tank, and allow to cool before storage. · If you drop or severely knock your iron this could cause internal damage even if the outside appears alright. Have it checked by a qualified electrician. · It is recommended that you use up one beaker of water by operating your iron's steam and shot of steam functions before ironing any clothes as some dripping may occur while your irons steam system is activated. Electrical requirements Check that the voltage on the rating plate of your appliance corresponds with your house electricity supply which must be A. C. If the socket outlets in your home are not suitable for the plug supplied with this appliance the plug should be removed and the appropriate one fitted. WARNING : The plug removed from the mains lead, if severed, must be destroyed as a plug with a bared flexible cord is hazardous if engaged into a live socket outlet. Should the fuse in the 13 amp plug require changing a 13 amp BS1362 fuse must be fitted. WARNING: THIS APPLIANCE MUST BE EARTHED. Instructions for use Temperature guide Heat setting markings on the adjustable control dial of all Morphy Richards irons match those of the International Textile Care Labelling Code. Symbol (120°C Max) Cool Control knob positions Fabric Do not iron at all Nylon, Acetates e. g. Acrilan Courtelle, Orlon Triacetates, e. g. Tricel/Polyester Iron on wrong side if moisture required use damp cloth (Not Acetate) Dry and spray Wool, Polyester mixtures e. g. Polyester/Cotton Cotton, Linen Rayon, Rayon mixtures, e. g. Rayon/Linen Fabrics requiring this setting usually require steam pressing for heavy cotton, denim etc. Steam/spray/shot of steam Jet clean Without water in tank Dry ironing (160°C Max) Warm (210°C Max) Hot Ironing With water in tank 3 Ion 441375253 Rev 2 10/12/03 11:43 AM Page 5 Components of your iron ¤ / Filling 1 Make sure that the iron is not plugged in and then set the variable steam control / to the ` ' position before filling the iron with water. 2 Push the filler cap release button fi and lift up the fill cap. Fill the water through the filling hole > into the water tank , , using the beaker provided. In hard water areas the use of distilled or demineralised water is recommended. Never use battery topping up fluid or water containing any substances like starch, or sugar, or defrosted water from a refridgerator. 3 Always pour out the remaining water after use. Warning: When filling your iron with tap water always use the beaker provided. A < > fi fl / ¤ < > fi fl · , , , · , Variable steam control Spray button Shot of steam button Filling hole with cap Filler cap release button Spray nozzle Soleplate Temperature control dial with indicator Water tank Anti-scale cartridge (certain models only) Temperature indicator light (red) , , Before use Note: The steam facility should only be used on garments which are suitable for ironing at the 2 and 3 dot settings. When ironing with the steam facility at the 2 dot setting, the steam output should be set at the lower end of the steam range (see variable steam section). [. . . ] To activate the anti-scale system you must place the anti-scale cartridge with sachet, as described below. Refilling intervals How often you need to refill your antiscale cartridge depends on how often you use your iron with its steam functions and how `hard' your water supply is. Water hardness varies greatly from one area to another. For advice on the relative hardness of your water, contact your local water supplier. [. . . ]