User manual MORPHY RICHARDS IB40617

[. . . ] 5 Morphy Richards are not liable to carry out any type of servicing work, under the guarantee. 6 Plastic filters for all Morphy Richards kettles and coffee makers are not covered by the guarantee. This guarantee does not confer any rights other than those expressly set out above and does not cover any claims for consequential loss or damage. This guarantee is offered as an additional benefit and does not affect your statutory rights as a consumer. [. . . ] · The socket should always be off before plugging or unplugging from the socket. Never yank the cord to disconnect from the socket, instead, grasp plug and pull to disconnect. · Do not allow the cord to touch hot surfaces. Let the iron cool completely before putting away. Loop cord loosely around the iron before storing. 2 Comfi iron 441375234 Rev 3 31/1/03 11:43 PM Page 4 Electrical requirements Check that the voltage on the rating plate of your appliance corresponds with your house electricity supply which must be A. C. If the socket outlets in your home are not suitable for the plug supplied with this appliance the plug should be removed and the appropriate one fitted. WARNING : The plug removed from the mains lead, if severed, must be destroyed as a plug with a bared flexible cord is hazardous if engaged into a live socket outlet. Should the fuse in the 13 amp plug require changing a 13 amp BS1362 fuse must be fitted. WARNING: THIS APPLIANCE MUST BE EARTHED. Instructions for use Temperature guide Heat setting markings on the adjustable control dial of all Morphy Richards irons match those of the International Textile Care Labelling Code. Symbol (120°C Max) Cool Control knob positions Fabric Do not iron at all Nylon, Acetates e. g. Acrilan Courtelle, Orlon Triacetates, e. g. Tricel/Polyester Iron on wrong side if moisture required use damp cloth (Not Acetate) Dry and spray Wool, Polyester mixtures e. g. Polyester/Cotton Cotton, Linen Rayon, Rayon mixtures, e. g. Rayon/Linen Fabrics requiring this setting usually require steam pressing for heavy cotton, denim etc. Steam/spray/shot of steam Jet clean Without water in tank Dry ironing (160°C Max) Warm (210°C Max) Hot Ironing With water in tank 3 Comfi iron 441375234 Rev 3 31/1/03 11:43 PM Page 5 Components of your iron ¤ < > fi fl / ¤ < > fi fl · , , , · , / , , Filling 1 Make sure that the iron is not plugged in and then set the variable steam control / to the `0' position before filling the iron with water. 2 Lift up the fill cap and fill the water through the filling hole > into the water tank ·, using the beaker provided. In hard water areas the use of distilled or demineralised water is recommended. Never use battery topping up fluid or water containing any substances like starch, or sugar, or defrosted water from a refridgerator. 3 Always pour out the remaining water after use. Warning: When filling your iron with tap water always use the beaker provided. A Variable steam/steam boost control Shot of steam button Spray button Filling hole with cap Spray nozzle Soleplate Temperature control dial with indicator Water tank Life long anti-scale (certain models only) Temperature indicator light (red) Auto-shut off light (green) (certain models only) Before use Note: The steam facility should only be used on garments which are suitable for ironing at the 2 and 3 dot settings. When ironing with the steam facility at the 2 dot setting, the steam output should be set at the lower end of the steam range (see variable steam section). Textiles and clothes are supposed to carry ironing instructions. If they don't you should follow the fabric guide on page 3, but be sure to test the temperature by ironing the hem of the garment or similar area first. [. . . ] To clean a stainless steel or anodised soleplate (certain models only) To keep the soleplate of your iron clean and free of limescale, we recommend that you use one of the gentle chrome, silver or stainless steel cleaners that are generally available. Always follow the manufacturers instructions. To clean off melted man-made fibres set the iron at 3 dot position and pass it over a clean piece of cotton which will draw the deposit off the surface. To clean a coated soleplate (certain models only) In the unlikely event of any man-made fibre fusing to the soleplate, set the iron at the 3 dot position and pass it over a clean piece of cotton which will draw the deposit off the surface. [. . . ]