User manual MORPHY RICHARDS IB75120

[. . . ] · Do not insert pins or any sharp objects into the blanket. · Do not tuck the heated part of material under the mattress. · Do not use if the blanket is wet. · Avoid pressing creases or folds into the blanket. [. . . ] The fact that this blanket incorporates the overheat system does not absolve the user from observing these instructions. Dual control models Each side of the blanket has a completely separate element and each is supplied with its own independant mains lead. Do not connect both flexible cords to one 13amp plug. The two leads should preferably be plugged into individual sockets. However, if only one socket is accessible, then a dual adaptor should be used. WARNING: Only the electric blanket should be connected to the dual 3 S1 Rev 2 21/7/04 1:43 PM Page 4 Underblanket with tie tapes · Use only as an underblanket and do not use above the occupant of the bed. · The blanket must be secured to the mattress in the following manner. Place the blanket directly on the mattress and ensure that a space of 10-15cm (4-6 inches) is left between the bottom edge of the blanket and mattress. · WARNING: Ensure the blanket is not folded, rucked or creased. When in use do not cover with pillows. Underblanket without tie tapes · Use only as an underblanket and do not use above the occupant of the bed. · WARNING: Ensure the blanket is not folded, rucked or creased. When in use do not cover with pillows. Fitting instructions 1 Place the blanket directly on the mattress, with the control switch end at the head of the bed. · The blanket must be secured to the mattress in the following manner. Place the blanket directly on the mattress and ensure that a space of 10-15cm (4-6 inches) is left between the bottom edge of the blanket and mattress (see diagram B). Fitting instructions 1 At the starting position the tape must be passed under the corner of the mattress, threaded up through the centre eyelet, passed under the adjacent corner, threaded through both eyelets on the long side of the blanket, passed under bottom corner, threaded through centre eyelet, passed under the remaining corner and finally tied securely to the corner eyelet at the finish position (see diagram A). · If the blanket is stretched too tightly, not allowing for `give' of mattress when the bed is occupied, distortion of the edges may take place. A B 10-15 cm 4-6 inches 10-15 cm 4-6 inches 4 S1 Rev 2 21/7/04 1:43 PM Page 5 Mattress covers with elasticated corner tapes 1 Place the mattress cover directly on the mattress with the control switch end at the head of the bed. 2 Turn the elastic corners underneath the mattress to secure in place (see diagram C). · Ensure all creases are smoothed out. Mattress protectors with elasticated skirt 1 Place the mattress cover directly on the mattress with the control switch end at the head of the bed. 2 Fit the shaped corners to the mattress and turn the elasticated edges of the skirt under the mattress (see diagram D). · Ensure all creases are smoothed out and the skirt fits tightly round the sides of the mattress. C D 5 S1 Rev 2 21/7/04 1:43 PM Page 6 Switch control Features / fi ¤ < > / Illuminated heat setting light (To identify heat levels in the dark) ¤ Heat levels 2 & 3 (Used to pre-heat) < Heat level 1 (Safe & comfortable to sleep all night) > Braille markings (located on the back of the switch) fi Off position How to use 1 Ensure the blanket is fitted to the bed correctly. 2 Plug the power lead into the closest socket, using an extension lead if needed to ensure that the lead is not stretched. All night use 1 Move the heat setting on the control switch to heat level 1. · This setting will provide safe and comfortable heat to sleep on all night. · This setting can be used to air the bed. WARNING: Always ensure that the heat setting is moved to the OFF position when you get up the next day, or after airing the bed. Preheating the bed 1 Move the heat setting on the control switch to heat level 2 or 3, depending on the level of the heat required. [. . . ] A standard service charge (inclusive of packing and return carriage) is made for routine inspection where no repair is found to be necessary. If the blanket fails to operate, check the following before returning: 1 Ensure that the plug and socket have not become disconnected. 2 Check that the supply plug is correctly connected to the flex. 3 Check the supply fuse and the 3 amp plug fuse if applicable. [. . . ]