User manual MORPHY RICHARDS IB75204

[. . . ] · Do not insert pins or any sharp objects into the blanket. · Do not tuck the heated part of material under the mattress. · Do not use if the blanket is wet. · Avoid pressing creases or folds into the blanket. [. . . ] However, if only one socket is accessible, then a dual adaptor should be used. WARNING: Only the electric blanket should be connected to the dual 3 S7 Rev 2 21/7/04 1:56 PM Page 4 Underblanket without tie tapes · Use only as an underblanket and do not use above the occupant of the bed. · WARNING: Ensure the blanket is not folded, rucked or creased. When in use do not cover with pillows. Mattress covers with elasticated corner tapes 1 Place the mattress cover directly on the mattress with the control switch end at the head of the bed. 2 Turn the elastic corners underneath the mattress to secure in place (see diagram B). · Ensure all creases are smoothed out. Fitting instructions 1 Place the blanket directly on the mattress, with the control switch end at the head of the bed. · The blanket must be secured to the mattress in the following manner. Place the blanket directly on the mattress and ensure that a space of 10-15cm (4-6 inches) is left between the bottom edge of the blanket and mattress (see diagram A). A B 10-15 cm 4-6 inches 4 S7 Rev 2 21/7/04 1:56 PM Page 5 Switch control Features / Illuminated heat setting light (Red for preheat level, green for safe all night level) ¤ Variable heat levels (For exact heat preference) < Braille markings (located on the back of the switch) > Timer off (Automatically turns the heat off after the number of hours selected) fi Timer on (Automatically turns the heat on in 3 hours time) fl Off setting Sleep button (Turns the heat on for 30 minutes to help you drop off to sleep or to air the bed in the morning) · Power `on' indicator light > · ¤ < fi fl / How to use 1 Ensure the blanket is fitted to the bed correctly. 2 Plug the power lead into the closest socket, using an extension lead if needed to ensure that the lead is not stretched. All night use 1 Select the required timer off setting. 2 Set the heat setting on the control switch to the low/minimum heat. This setting will provide safe and comfortable heat to sleep on all night. · This setting will provide safe and comfortable heat to sleep on all night. · This setting can be used to air the bed. WARNING: Always ensure that the heat setting is moved to the OFF position when you get up the next day. Preheating the bed 1 Turn the blanket on by setting one of the timer off settings /, < or Â. 2 Set the heat setting on the control switch to maximum heat, the light indicator will show a red light to indicate that the preheating has been selected. Allow approximately 10-20 minutes for a light heat and a further 20-30 minutes for the blanket to heat the bed thoroughly, although this time may vary depending on room temperature. Braille markings · Braille markings are located on the back of the switch to help identify the direction of the heat level in the dark, or if visually impaired. · The highest heat level pre-heat is identified by 3 raised nodules mid level by 2 raised nodules low level (all night) by 1 raised nodule 5 S7 Rev 2 21/7/04 1:56 PM Page 6 Sleep button 1 Press this button to turn the heat on for 30 minutes. The light will flash to indicate that the sleep function has been selected, and it will automatically turn off after 30 minutes. This is ideal to help you get back to sleep if you wake in the night and are cold, or to air the bed in the morning. · Note: This function will only operate if the blanket is switched to a timer on or off setting, not if the switch is at the OFF position. 2 Only use in a washing machine with a drum large enough to take the blanket without forcing it in. Machine washing 40º Setting the timer 1 To program the heat to turn on in 3 hours time, move the timer button to the unfilled 3 symbol . This allows you to come home to a warm bed. Ensure that the heat setting is set to pre-heat, maximum heat level. [. . . ] 2 Check that the supply plug is correctly connected to the flex. 3 Check the supply fuse and the 3 amp plug fuse if applicable. Service department Waterside Mill Langham Street Rosegrove Burnley BB12 6AL Republic of Ireland c/o Dimpco Ltd Airport Road Cloghran Co. Dublin 0870 060 2616 1800 409089 7 S7 Rev 2 21/7/04 1:56 PM Page 8 Your three year guarantee It is important to retain the retailers receipt as proof of purchase. [. . . ]