User manual MOTOROLA DCT2000

[. . . ] DCT 2000 7IAH /KE@A CURSOR MESSAGES A/B REMOTE POWER A/B CHANNEL GUIDE INFO MENU SELECT POWER NOTE TO CATV SYSTEM INSTALLER CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This reminder to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close as possible to the point of cable entry as practical. EXAMPLE OF ANTENNA GROUNDING EXAMPLE OF ANTENNAGROUNDING Electric service equipment Ground clamp Antenna lead in wire Graphical symbols and supplemental warning marking locations on bottom of terminal. WARNING TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE, OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of unisulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point, within an equilateral triangle, is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. [. . . ] 25 Baseband with Dolby Digital. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 INTRODUCTION Your DCT 2000 includes one or more of the following features: · · · · · · · · · Remote control Volume control Parental control Favorite channel recall Sleep and alarm timers Easy Pay-Per-View purchases Electronic program guide (EPG) Video on Demand Digital audio Congratulations on your purchase of the state-of-the-art DCT 2000 digital consumer terminal. The DCT 2000 brings unsurpassed digital audio and video quality to your TV viewing. Electronic program guide menus provide convenient control of selecting and viewing programs. It's simple to set up and easy to operate. You can purchase Pay-Per-View special events, recent movies or Video on Demand. Video on Demand is similar to renting a video, including the ability to pause, rewind, and fast forward. This guide introduces you to the features and operation of the DCT 2000. Access to the DCT 2000 features is gained through the electronic program guide. Be sure to read your electronic program guide instruction manual to get the most out of your DCT 2000. 2 INTRODUCTION Front Panel The DCT 2000 front panel has 12 keys and an LED display. Use the keys to perform basic functions such as changing channels and powering on and off. Left/right RCA stereo outputs connect the DCT 2000 to your stereo. ® 7 INTRODUCTION Item 11 12 13 14 15 VIDEO TV Pass card slot Data outputs IR Output AC power Description This RCA video output connects the DCT 2000 to a composite (baseband) TV. For future use with high-speed, high-definition components. An RCA output connecting the optional Infrared (IR) Blaster attachment for your DCT 2000. The bottom plug is for attaching a power cord. The top plug can be configured for plugging in another device such as a TV or VCR. 8 INTRODUCTION A CABLE IN B Rear Panel Options There are four rear panel options that can be included on your DCT 2000. Item Sw itch o ptio n s 1 RF IN CONV IN Description This contains coaxial input connectors used in a dual cable system and with an A/B box. These coaxial connectors enable the cable signal to bypass the DCT 2000 and go directly to a cable-ready TV or VCR. These coaxial connectors are used in a dual cable system. The cable signal from A or B goes directly to a cable-ready TV or VCR. The Telco Return Impulse Pay-Per-View option is a telephone connection module that enables you to purchase special programming on one-way cable systems. RF OUT 1 2 A/B Switch RF Bypass 2 3 A RF OUT DUAL A/B-RF BYPASS B 4 Telco Return 3 PHONE IP PV o ptio n 4 9 RECORDING YOUR CONNECTIONS A/B In A CABLE IN B B R F Bypass RF OUT RF IN CONV IN Du al A/B R F Bypass A RF OUT Telco re tu rn Use this diagram to record cable connections from the rear panel. [. . . ] The RF Bypass enables you to view an unscrambled analog channel on a TV while recording another channel through the DCT 2000. TV AUDIO IN CABLE IN AUDIO OUT R L VIDEO IN S-VIDEO IN CABLE OUT R L VIDEO OUT S-VIDEO OUT 21 CONNECTING YOUR DCT 2000 In these illustrations the baseband connectors on entertainment components are labeled R for right audio, L for left audio, V or VIDEO, and S or S-VIDEO. S-VIDEO RF IN CAB LE IN R L AUDIO OUT VIDEO T V Pa ss Ca rd DATA HIGH SPEED OU OF T BAND IR AUX AUD IO IN TO T V/ VCR SPDIF TO RF IN SW ITCHED 105-12 5V 60Hz 4A MAX 500W M AX Composite Baseband and S-Video Connecting the DCT 2000 using the baseband RCA type outputs enables ® you to experience stereo and Dolby Surround sound on digital channels when available. D CT 20 0 0 AUDIO IN R CABLE IN AUDIO OUT VIDEO OUT S-VIDEO OUT L VIDEO IN S-VIDEO IN When connecting the video path, never connect baseband composite video and S-Video together. Because some entertainment equipment will not support both video inputs simultaneously, use only one connection path. TV 22 CONNECTING YOUR DCT 2000 D CT 20 0 0 AUX AUD IO IN TO T V/ VCR RF IN CAB LE IN R L AUDIO O UT VIDEO T V P ass Ca rd DATA Composite VCR Cabling SPDIF S-VIDEO HIGH SPEED OU OF T BAND IR TO RF IN SW ITCHED 105-12 5V 60Hz 4A MA X 500W M AX This diagram illustrates how to connect the DCT 2000 to a VCR using the audio connectors on the VCR. When connecting the video path, never connect baseband composite video and S-Video together. Because some entertainment equipment will not support both video inputs simultaneously, use only one connection path. AUDIO IN CABLE IN AUDIO OUT R L VIDEO IN S-VIDEO IN CABLE OUT R L VIDEO OUT S-VIDEO OUT TV AUDIO IN R CABLE IN AUDIO OUT L VIDEO IN VIDEO OUT S-VIDEO IN S-VIDEO OUT 23 CONNECTING YOUR DCT 2000 D CT 20 0 0 AUX AUD IO IN TO T V/ VCR RF IN CAB LE IN R L AUDIO O UT VIDEO T V P ass Ca rd DATA Stereo Cabling Diagram (VCR to Stereo) SPDIF S-VIDEO HIGH SPEED OU OF T BAND IR TO RF IN SW ITCHED 105-12 5V 60Hz 4A MA X 500W M AX This diagram illustrates how to connect the DCT 2000 to a stereo using the audio connectors on the VCR. [. . . ]