User manual MOTOROLA DCT5100 BIS

[. . . ] DCT5100 Digital Consumer Terminal Installation Manual CURSOR INFO MSGS. P CHANNEL A/B A/B MENU ON MUTE GUIDE REMOTE SMART CARD SELECT POWER USB VIDEO IN L AUDIO IN R CAUTION RISK OF ELECTRIC SHOCK CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Caution These servicing instructions are for use by qualified personnel only. To reduce the risk of electrical shock, do not perform any servicing other than that contained in the Installation and Troubleshooting Instructions unless you are qualified to do so. Refer all servicing to qualified service personnel. Special Symbols That Might Appear on the Equipment This symbol indicates that dangerous voltage levels are present within the equipment. [. . . ] Perform the boot cycle, including the download for the DCT5100. For details, refer to the boot cycle routine at the end of this section. Perform the basic operational check in this section after installing the DCT5100. 6 7 8 DCT5100 Installation Manual 3-2 Installation Standard Cabling Diagram Standard cabling for cable service is connecting the DCT5100 to a VCR. Figure 3-1 illustrates the basic RF cabling diagram that enables you to record on your VCR the currently tuned channel. When a VCR is not present, connect the coax cable from the DCT5100 directly to the CABLE IN connector on the TV. The output from the RF connection will be on channel 3 or 4, depending on the configuration information coming from the control system. Figure 3-1 Standard VCR cabling DCT 5100 AUDIO IN R L VIDEO OUT ETHERNET SPDIF IN TO TV/VCR CABLE IN IR HPNA TV Pass Card S-VIDEO IEEE 1394 USB R L AUDIO OUT Y Pb Pr OPTICAL SPDIF SWITCHED 105-125V 60Hz 4A MAX 500W MAX CONVENIENCE OUTLET From cable outlet VCR (optional) R CABLE IN L VIDEO IN SVIDEO IN CABLE IN CABLE OUT AUDIO OUT VIDEO OUT SVIDEO OUT R L VIDEO IN AUDIO IN R L AUDIO IN R L TV SVIDEO IN AUDIO OUT VIDEO OUT SVIDEO OUT The RF connection does not carry stereo for digital channels. To receive stereo on digital channels, connect the DCT5100 using RCA baseband connectors illustrated later in this section. DCT5100 Installation Manual Installation 3-3 RF Bypass Switch Cabling Diagrams The RF Bypass switch enables the cable signal to pass directly to a cable-ready TV, bypassing the DCT5100. The bypass mode is automatically initiated under one of three conditions: when the DCT5100 loses power, when it is turned off from the front panel, or when the user manually activates the switch by pressing the A/B key. If the DCT5100 loses power or is turned off, the subscriber can continue viewing the clear analog channels on the cable system. Activating bypass mode enables you to tape a tuned channel from the DCT5100 while watching a different clear channel that is bypassed to the TV. Proper operation of the RF Bypass feature requires special configuration information from the control system, and proper user interface settings in the Electronic Program Guide (EPG). Figure 3-2 illustrates RF cabling to an optional VCR using the RF Bypass switch. When a VCR is not present, install the supplied jumper cable from the CONV OUT to CONV IN on the RF Bypass switch. Figure 3-2 RF Bypass switch TV R L AUDIO IN R CABLE IN AUDIO OUT VIDEO OUT SVIDEO OUT L VIDEO IN SVIDEO IN DCT 5100 AUDIO IN R L VIDEO OUT ETHERNET SPDIF IN RF OUT CONV OUT CABLE IN CONV IN IR HPNA TV Pass Card S-VIDEO IEEE 1394 USB R L AUDIO OUT Y Pb Pr OPTICAL SPDIF SWITCHED 105-125V 60Hz 4A MAX 500W MAX CONVENIENCE OUTLET From cable outlet VCR (optional) R CABLE IN L VIDEO IN SVIDEO IN AUDIO IN R L CABLE OUT AUDIO OUT VIDEO OUT SVIDEO OUT The DCT5100 RF output does not carry stereo for digital channels. All VCR recordings made using this connection will be in mono for digital channels. DCT5100 Installation Manual 3-4 Installation Audio/Video Cabling Diagrams The DCT5100 is capable of delivering Dolby AC-3 audio to a Dolby Digital stereo receiver using the SPDIF RCA connector. When connecting to a receiver, you can use the left/right RCA baseband audio outputs or the SPDIF RCA connection. The connections you use will depend on the capabilities of the audio receiver. The SPDIF port carries the audio stream in either a PCM or Dolby AC-3 format. If the subscriber does not have a Dolby Digital receiver, use the baseband Left/Right audio RCA connections to interface to the audio receiver. The following illustrations show audio/video connections to a digital receiver, where the receiver functions as an audio/video router. When connecting the audio path to a digital receiver, reference your receiver's installation instructions for directions on connecting to baseband and SPDIF ports. DCT5100 Installation Manual Installation 3-5 The VCR and TV receive their audio/video signals from the currently selected input device on the digital receiver. This is important when the subscriber has another audio/video device such as a DVD player, a secondary VCR, a CD player, or other electronic component. It is recommended that you connect the TV to the monitor output so On-Screen menus associated with the receiver can be displayed. [. . . ] Set-top interactive state is running, sending idle messages, and waiting for any Prepare for Poll or MAC messages. Set-top interactive run state has stopped and set-top is waiting for status or transmission control message. Set-top interactive state is unknown or invalid. IL WAIT_LM_ACK I SO I LA WAIT_SO_ACK WAIT_LA_OR_SO SI r dc r S 00 INIT_STOPPED RUN_WAIT_DC_OR_C RUNNING RUN_STOPPED INVALID DCT5100 Installation Manual 4-36 Diagnostics MAC ABORT COUNTER The MAC ABORT COUNTER increments every time the MAC layer reaches the Cell Abort Count limit. The MAC ABORT COUNTER is reset by the successful upstream transmission of a cell, for example, when an ACK is received by the set-top. [. . . ]