User manual MOTOROLA HIGH-DEFINITION OFF-AIR TUNER HDT100

[. . . ] User Guide HDT100 High Definition Tuner POWER SIGNALLOSS MENU ENTER POWER EXIT IMPORTANT SAFETY INSTRUCTIONS 1 2 3 4 5 6 7 8 Read instructions All the safety and operating instructions should be read before the appliance is operated. Retain instructions The safety and operating instructions should be retained for future reference. Heed warnings All warnings on the appliance and in the operating instructions should be adhered to. Follow instructions All operating and use instructions should be followed. [. . . ] IN Pr Audio cable TV INPUT AUDIO LEFT AUDIO RIGHT 14 Audio Connections To hook up your audio connections: Connect the stereo audio cable supplied with your HDT100 to the L and R connectors on the HDT100 and the INPUT AUDIO LEFT and RIGHT connectors on your TV. Now proceed to the next step--connecting your antenna and power cord. 15 INSTALLING THE HDT100 HDT100 Manufactured under license from D olby Laboratories. Dolby and the double -D symbol are trademarks of Dolby Laboratories. Y VIDEO Pb 100~240V AC 50~60 Hz , 2A RS -232 OPTICAL L Pr S-VID EO - R ANT. IN To wall outlet To antenna 16 Connecting the Antenna and Power Cord You can use an outdoor or indoor antenna to receive over-the-air high definition TV signals: 1 2 Connect your antenna's coaxial cable to the ANT IN connector on your HDT100. Plug the power cord supplied with your HDT100 into the HDT100's power connector and then plug the cord into a wall outlet. Now that you've completed hooking up your HDT100, you're ready to program your HDT100 with over-the-air digital TV stations. Proceed to "Auto Scan" on the following page for instructions. 17 AUTO SCAN Before you can start using the HDT100, you need to program it with the station numbers of the over-the-air digital TV stations available in your area. This can be done by simply running auto scan from the HDT100's on-screen menu. You can navigate the on-screen menu from the HDT100's front panel or by using the remote control: · · · Use the !and "arrow keys to move up and down the on-screen menu Use the SELECT button to select the highlighted item on the on-screen menu Use the EXIT button to return to the main menu from a submenu or to leave the main menu To run auto scan: 1 2 Press the POWER button on the HDT100 front panel or remote control to turn on the receiver. Press MENU on the remote control or MENU/ENTER on the front panel. The Menu screen is displayed: 3 Using the "arrow key, highlight Installation and press SELECT. The Password window is displayed. 18 4 Enter your four-digit password. If you have not yet created your own password, enter the default password: 0000. The Installation menu is displayed: If you wish to change your password, see "Changing Your Password" on page 28. 5 Highlight Auto Scan and press SELECT. The HDT100 starts scanning from Channels 2 to 69. The entire scan will take about four minutes. An indicator is displayed showing the scan's progress: 19 As each digital TV signal is scanned, you'll see the signal's channel number and program name displayed on the Program List: The auto scan will end on channel 69. 6 7 Press EXIT to return to the main menu. Press EXIT again to exit the main menu and start enjoying digital TV programs!If the picture displayed on your TV is too small, use the A. RATIO button on your remote control to change the picture size. 20 OPERATION Once your HDT100 is hooked up to your antenna and TV and you've added your TV channels, you can enjoy digital over-the-air TV programs. Simply use the remote control supplied with your HDT100 to change channels, view program information, and navigate the on-screen menus. [. . . ] If your problem still exists, contact your service provider. Problem The POWER LED on the front panel does not light up Possible Solution Confirm the power cord is plugged into a functioning power outlet. Press POWER on the front panel to see if the LED lights up. Determine if the HDT100 is in "standby" mode by pressing STANDBY on the remote control. No picture Check to be sure that all cables are connected properly (hand-tighten if necessary). [. . . ]