User manual MOTOROLA HS810

[. . . ] When the headset's battery is fully charged (about 2 hours), the indicator light turns off. 2 Scroll to Power. 5 Press Select to turn on the Bluetooth feature. The Bluetooth feature remains on until you turn it off. Note: These steps are for most Motorola phones. [. . . ] For other phones, see your phone's user's guide. 2 Disconnect the charger. Note: Headset is not functional while charging. or visit us at www. hellomoto. com 3 PAIR Your Headset Motorola, Inc. Consumer Advocacy Office 1307 East Algonquin Road Schaumburg, IL 60196 www. hellomoto. com 1-877-MOTOBLU 1-800-331-6456 (United States) 1-888-390-6456 (TTY/TDD United States for hearing impaired) 1-800-461-4575 (Canada) Guide Number: 6809495A04-O When you see this symbol on a Motorola product, do not dispose the product with household waste. Before you can use your headset, you must pair (link) it with your phone. Step A - PUT THE HEADSET IN PAIRING MODE Indicator Light 1 Ensure the headset is turned off (indicator light not blinking). 2 Press and hold the Call E button for 4 or 5 seconds. The indicator light will initially flash, but continue to hold down the button until the indicator light is steadily lit. If the indicator light is flashing or not steadily lit when releasing the button, repeat both steps 1 and 2 on this page. MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. The use of wireless devices and their accessories may be prohibited or restricted in certain areas. Always obey the laws and regulations on the use of these products. The Bluetooth trademarks are owned by their proprietor and used by Motorola, Inc. If the Bluetooth feature was turned off or was turned on only temporarily, you may need to restart the Bluetooth feature (see step 2) and pair your phone and headset again (see step 3). If you need more help, contact us at 1- 877-MOTOBLU. FOR DETAILS ABOUT YOUR HANDSFREE DEVICE See the user's guide or visit us at www. hellomoto. com/bluetooth and click Support. Features and Functions Guide HS810 Bluetooth® Handsfree Headset TURNING ON AND OFF To turn on the headset, press and hold the Call E button on your headset until the indicator light begins flashing. The indicator light blinks when the power is on. To turn off the headset, press and hold the Call E button on your headset for 5 seconds. The indicator light will flash rapidly and then stop flashing. Call Button IMPORTANT: Be sure to first follow the instructions on the reverse side to complete initial setup of your HS810 Indicator Light WEARING THE HEADSET 1 Open the earhook. [. . . ] Call Button IMPORTANT: Be sure to first follow the instructions on the reverse side to complete initial setup of your HS810 Indicator Light WEARING THE HEADSET 1 Open the earhook. 4 Point the microphone toward your mouth. CHANGING FOR USE ON OTHER EAR You can wear your HS810 headset on your left or right ear. To change ear orientation, simply flip the earhook all the way over. ADJUSTING VOLUME To adjust the volume on your headset, press the Volume Up or Volume Down button until you reach the desired volume level. Volume Buttons When increasing (or decreasing) speaker volume, a single audio tone is heard when reaching maximum (or minimum) level. MAKING CALLS Function Make a voice dial call Action Tap the Call E button and speak the name after the tone Tap the Call E button Press and hold the Call E button until you hear a beep Tap the Call E button Press and hold the Call E button until you hear a beep MAKING CALLS CONTINUED Function Answer a second incoming call Toggle between two active calls Action Press and hold the Call E button (places first call on hold) Press and hold the Call E button (places other call on hold) Press and hold the Call E button until you hear a beep Tap the Call E button End a call Redial a number Put an active call on hold or resume a call Transfer a call from the phone to the headset Receive a call Reject a call Note: Your HS810 supports both Handsfree and Headset Profiles. [. . . ]