User manual MOTOROLA SBV5222 SURFBOARD DIGITAL VOICE MODEM

[. . . ] User Guide SBV5222 SURFboard® Digital Voice Modem Introduction Installation Troubleshooting Glossary License Safety and Regulatory Information IMPORTANT SAFETY INSTRUCTIONS - when using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: · · · · · Read all of the instructions listed here and/or in the user manual before you operate this device. Give particular attention to all safety precautions. Retain the instructions for future reference. This device must be installed and used in strict accordance with manufacturer's instructions as described in the user documentation that is included with the device. [. . . ] For those systems, you can connect through Ethernet only. Caution! Be sure the SURFboard Voice Modem CD-ROM is inserted in the CD-ROM drive before you plug in the USB cable. SBV5222 SURFboard® Digital Voice Modem 12 Introduction Installation Troubleshooting Glossary License Setting Up a USB Driver in Windows 2000 1 2 Insert the SURFboard Voice Modem CD-ROM in the CD-ROM drive. This CD contains the USB drivers and must be inserted and read by the PC before you connect the digital voice modem to the PC. Connect the digital voice modem to your computer with a USB cable. For further instructions, see "Cabling and Startup for a Single User" on page 10. A few seconds after you complete the USB connection, the Found New Hardware Wizard window is displayed: 3 Click Next. The following window is displayed: Although your digital voice modem model number may be different than in the images in this guide, the procedure is the same. Be sure "Search for a suitable driver for my device" is selected. SBV5222 SURFboard® Digital Voice Modem 13 Introduction Installation Troubleshooting Glossary License 4 Click Next. The following window is displayed: Be sure "CD-ROM drives" is the only box selected. 5 Click Next. The following window is displayed: 6 Click Next. If the Insert Disk window is displayed, be sure the SURFboard Voice Modem CD-ROM is in the CD-ROM drive and follow steps 7 to 11. Otherwise, if the Completing the Found New Hardware window is displayed, you can skip to step 12. SBV5222 SURFboard® Digital Voice Modem 14 Introduction Installation Troubleshooting Glossary License 7 On the Insert Disk window, click OK. The Files Needed window is displayed: 8 9 If necessary, select your CD-ROM drive in the "Copy files from" list. Click Browse. 10 Double-click the NetMotCM. sys file in the CD-ROM root directory. The Files Needed window is displayed: 11 Click OK. The Found New Hardware Wizard window is displayed: 12 Click Finish to complete the installation. When you finish setting up the USB driver, you can continue with "Configuring TCP/IP in Windows 2000" on page 17. If you have any difficulties setting up the USB driver, perform "Removing the USB Driver from Windows 2000" on page 34 and repeat this procedure. SBV5222 SURFboard® Digital Voice Modem 15 Introduction Installation Troubleshooting Glossary License Setting Up a USB Driver in Windows XP 1 2 Insert the SURFboard Voice Modem CD-ROM in the CD-ROM drive. This CD contains the USB drivers and must be inserted and read by the PC before you connect the digital voice modem to the PC. Connect the digital voice modem to your computer with a USB cable. For further instructions, see "Cabling and Startup for a Single User" on page 10. A few seconds after you complete the USB connection, the Found New Hardware Wizard window is displayed: 3 4 Be sure "Install the software automatically" is selected. Windows automatically searches for the correct USB drivers and installs them. If the installation is successful, the following window is displayed: Although your digital voice modem model number may be different than in the images in this guide, the procedure is the same. 5 Click Finish to complete the installation. [. . . ] Motorola and its 3rd party licensors retain the ownership of the Software. You may: USE the Software only in connection with the operation of the Product. TRANSFER the Software (including all component parts and printed materials) permanently to another person, but only if the person agrees to accept all of the terms of this License. If you transfer the Software, you must at the same time transfer the Product and all copies of the Software (if applicable) to the same person or destroy any copies not transferred. [. . . ]