User manual MOTOROLA T720 CDMA

[. . . ] MORE HERE > Welcome Welcome to the world of Motorola digital wireless communications!We are pleased that you have chosen the Motorola T720 CDMA wireless phone. This reference guide is a companion to the user guide that is packaged with the Motorola T720 CDMA wireless phone. Refer to the user guide for general information about using the phone. [. . . ] Be careful not to drain your vehicle battery if you select this option. 17 Serial Cable Action 1 Plug the serial cable into the detachable head. Make sure that the Motorola logo on the detachable head and the metal shielding on the serial cable plug are both facing you. 2 With the Motorola logo and the phone both facing you, plug the detachable head into the phone's accessory connector port. 3 Plug the other end of the cable into the serial interface connection on the device and tighten the screws, if present. USB Cable Action 1 Plug the end of the cable with the Motorola logo into the phone's accessory connector port. Make sure that the logo and the phone are both facing you. 2 Plug the other end--the USB connection--into the USB port on the external device. Sending a Data or Fax Call Use this procedure to send data or a fax from a connected computer or hand-held device. Action 1 Make sure that the phone is connected and powered on 2 Open the application (such as dial-up-networking or fax) on your computer, and place the call through the application Note: You cannot dial data or fax numbers through your phone's keypad. You must dial them through your computer. 3 When the transfer is complete, end the call from the connected device to close the connection Receiving a Data or Fax Call Use this procedure to transfer data or a fax to a connected computer or hand-held device. Getting More Out Of Your Phone Setting Up Your Phone Find the Feature M > Settings > Connection > Incoming Call Action 1 Press CHANGE (+) to select Next Call 2 Press S to scroll to Data In Only or Fax In Only 3 Press SELECT (+) to set the call format 4 Connect your phone to the device to enable the data or fax transfer Note: You cannot answer incoming voice calls when your phone is in data or fax mode. Any voice calls you receive are treated as unanswered calls. To return a voice call, reset your phone to normal voice operation as described below. Synchronizing Data You can synchronize phonebook and datebook information between your phone, computer, and PDA with Starfish TrueSync® software, a Motorola accessory product. See the TrueSync user guide for more information. Note: TrueSync software is designed to synchronize with basic features of many popular Personal Information Management (PIM) software and hardware products. Transferring the Data or Fax Your phone notifies you when the data or fax call arrives, and transfers the call to the connected device. Use the application running on the device to answer the call. Ending the Data/Fax Connection When the data or fax transfer is complete, end the call from the connected device to close the connection. Resetting Normal Voice Operation After making a data or fax call, you must reset your phone to resume normal voice operation. Find the Feature M > Settings > Connection > Incoming Call > Next Call > Normal Your phone also reverts to normal voice operation when you turn it off and then turn it back on. 18 Adjusting Network Settings Your service provider registers your phone to its network. In some situations, such as using the phone as a modem or connecting it to a TTY device, you may need to change the network registration. Note: Some settings and/or options described in this section may not be available for all phone models. Press 1S 2 SELECT (+) To scroll to Automatic or Manual select the option Setting Service Tones You can set your phone to beep each time the network registration status changes. Find the Feature Press 1S 2 SELECT (+) M > Settings > Network Viewing Current Registered Network Find the Feature M > Settings > Network > Service Tone > Current Network To scroll to On or Off select the option Your phone displays the network ID. Setting Analog Only You can set your phone to place calls only on analog channels. Note: This feature may appear as an option on the Set Mode menu (see following section). Find the Feature Press 1S 2 SELECT (+) M > Settings > Network Setting Call Drop Alert You can set your phone to emit an alert tone whenever the network drops a call. [. . . ] My phone You must be in an area with digital beeped when I coverage. Check your phone's attached the display for the digital signal data cable, but indicator (F). my data and Some wireless networks may not fax support data or fax transmission. applications If you see the digital indicator, but do not work. [. . . ]