User manual MSI MS-7666 XPOWER V1.0

[. . . ] XPower series MS-7666 (v1. x) Mainboard G52-76661X1 Preface Copyright Notice The material in this document is the intellectual property of MICRO-STAR INTERNATIONAL. We take every care in the preparation of this document, but no guarantee is given as to the correctness of its contents. Our products are under continual improvement and we reserve the right to make changes without notice. Trademarks All trademarks are the properties of their respective owners. MSI® is registered trademark of Micro-Star Int'l Co. , Ltd. NVIDIA® is registered trademark of NVIDIA Corporation. [. . . ] TCG/TPM SUPPORT After installing the Trusted Platform Module, this field bacomes available. Setting the option to [Yes] enables TPM (Trusted Platform Module) for the system. Chapter 3 3-9 BIOS Setup Integrated Peripherals USB Controller This setting allows you to enable/disable the onboard USB controller. USB Device Legacy Support Select [Enabled] if you need to use a USB-interfaced device in the operating system. Onboard LAN Controller This setting allows you to enable/disable the onboard LAN controller. Onboard 2nd LAN Controller This setting allows you to enable/disable the onboard 2nd LAN controller. LAN Option ROM This item is used to decide whether to invoke the Boot ROM of the onboard LAN. Onboard IEEE1394 Controller This setting allows you to enable/disable the onboard IEEE1394 controller. Onboard E-SATA Controller Mode This item is used to select mode for E-SATA connectors. SATA 6Gb/s Controller Mode This item is used to select mode for SATA 6Gb/s devices. When you set "Disabled" in this field, the 6Gb/s controller will be disabled. Onboard USB 3. 0 Controller This setting is used to enable/disable the onboard USB 3. 0 controller. 3-10 MS-7666 On-Chip ATA Devices Press <Enter> to enter the sub-menu and the following screen appears: Chapter 3 PCI IDE BusMaster This item allows you to enable/ disable BIOS to used PCI busmastering for reading/ writing to IDE drives. On-Chip SATA Controller This item allows users to enable or disable the on-chip SATA controller. RAID Mode This item is used to select mode for on-chip SATA connectors. 3-11 BIOS Setup Power Management Setup Important S3-related functions described in this section are available only when the BIOS supports S3 sleep mode. ACPI Function This item is to activate the ACPI (Advanced Configuration and Power Management Interface) Function. If your operating system is ACPI-aware, select [Enabled]. ACPI Standby State This item specifies the power saving modes for ACPI function. EuP 2013 This item is designed for Energy Using Products Lot 6 2013 (EuP) aka Energy Related Products (ErP). To reduce Power Consumption when system off or standby mode. Note: When "Enabled" EuP 2013 setting, system don't support RTC wake up event function. S4/S5 PowerOn Wait (Sec) This item allows you to select a waiting period when system wake-up from power state S4/S5. 3-12 MS-7666 Restore On AC Power Loss This item specifies whether your system will reboot after a power failure or interrupt occurs. Settings are: [Off] Always leaves the computer in the power off state. [On] Always leaves the computer in the power on state. [Last State] Restore the system to the status before power failure or interrupt occurred. [. . . ] In the [Topology] pane, scroll to "Virtual Disk" (VD 0: XXXX), and press Enter to select. Scroll to "Rebuild" and press Enter to configure the rebuild process. Marvell BIOS Setup (c) xxxx Marvell Technology Group Ltd. Topology HBA 0: Marvell 0 Virtual Disks VD 0: MRAID1 PD 8: ST3750330MS [Delete] Free Physical Disks [Rebuild] PD 0: ST3750XXX Information ID Namd Status Stripe Size RAID Mode Size BGA Status Number of PDs Members : : : : : : : : : 0 MRAID1 Degrade 64K RAID1 953344MB N/A 2 08 Appendix C Appendix C 4. Scroll through the list of free disks, and press Space to select a replacement physical disk. [. . . ]