User manual MSI MS-91F7 V1.X

[. . . ] MS-91F7 (v1. X) Server Board Preface Copyright Notice The materal n ths document s the ntellectual property of MICRO-STAR INTERNATIONAL. We take every care n the preparaton of ths document, but no guarantee s gven as to the correctness of ts contents. Our products are under contnual mprovement and we reserve the rght to make changes wthout notce. Trademarks All trademarks are the propertes of ther respectve owners. MSI® s regstered trademark of Mcro-Star Int'l Co. , Ltd. NVIDIA® s regstered trademark of NVIDIA Corporaton. [. . . ] · Please refer to the documentation in the CPU fan package for more details about the CPU fan installation. · Confirm if your CPU cooler is firmly installed before turning on your system. 2-5 Hardware Setup MeMory These DIMM slots are intended for memory modules. DDR3 240-pin, 1. 5V 48x2=96 pin 72x2=144 pin Memory Population Rules In Multi-Channel mode, make sure that you install memory modules of the same type and density in different channel DIMM slots. CPU0_DIMM_A1 CPU0_DIMM_A0 CPU0_DIMM_B1 CPU0_DIMM_B0 CPU1_DIMM_B0 CPU1_DIMM_B1 CPU1_DIMM_A0 CPU1_DIMM_A1 For CPU0 Population Rules 1 DIMM 2 DIMMs 3 DIMMs 4 DIMMs CPU0_DIMM_A1 (1) CPU0_DIMM_A1 + CPU0_DIMM_B1 (Dual-Channel) (2) CPU0_DIMM_A1 + CPU0_DIMM_A0 (Single-Channel) CPU0_DIMM_A1 + CPU0_DIMM_A0 + CPU0_DIMM_B1 CPU0_DIMM_A1 + CPU0_DIMM_A0 + CPU0_DIMM_B1 + CPU0_DIMM_B0 For CPU1 Population Rules 1 DIMM 2 DIMMs 3 DIMMs 4 DIMMs CPU1_DIMM_A1 (1) CPU1_DIMM_A1 + CPU1_DIMM_B1 (Dual-Channel) (2) CPU1_DIMM_A1 + CPU1_DIMM_A0 (Single-Channel) CPU1_DIMM_A1 + CPU1_DIMM_A0 + CPU1_DIMM_B1 CPU1_DIMM_A1 + CPU1_DIMM_A0 + CPU1_DIMM_B1 + CPU1_DIMM_B0 2-6 MS-91F7 Installing Memory Modules 1. The memory module has only one notch on the center and will only fit in the right orientation. Insert the memory module vertically into the DIMM slot. Then push it in until the golden finger on the memory module is deeply inserted in the DIMM slot. The plastic clip at each side of the DIMM slot will automatically close when the memory module is properly seated. Manually check if the memory module has been locked in place by the DIMM slot clips at the sides. Important You can barely see the golden finger if the memory module is properly inserted in the DIMM slot. Notch Volt Important · To enable successful system boot-up, always insert the memory modules into the DIMM_A1 first. · If users intend to install two DIMMs, it is highly suggested that these DIMMs are populated in DIMM_A1 and DIMM_B1 for enhanced Dual-Channel memory performance. · In Dual-Channel mode, make sure that memory modules of the same type and density are installed in different channel DIMM slots. 2-7 Hardware Setup power SuppLy System Power Connector: JPWR1 Ths connector allows you to connect a power supply. To connect to the power supply, make sure the plug of the power supply s nserted n the proper orentation and the pins are aligned. Then push down the power supply firmly into the connector. PIN 1 2 3 4 5 6 7 8 9 10 11 12 SIGNAL +3. 3V +3. 3V GND +5V GND +5V GND PWR OK 5VSB +12V +12V +3. 3V PIN 13 14 15 16 17 18 19 20 21 22 23 24 SIGNAL +3. 3V -12V GND PS-ON# GND GND GND +3. 3VSB +5V +5V +5V GND 24 12 13 1 CPU/Memory Power Connector: JPWR2 Ths connector provdes 12V power output to the CPUs & memory. PIN 8 4 5 1 1 2 3 4 5 6 7 8 SIGNAL GND GND GND GND +12V +12V +12V +12V Important Make sure that all power connectors are connected to the power supply to ensure stable operation of the mainboard. 2-8 MS-91F7 rear paneL i/o Mouse Port VGA Port LAN Jack LAN Jack Keyboard Port Serial Port USB Port USB Port Mouse/Keyboard Port The standard PS/2 mouse/keyboard DIN connector s for a PS/2 mouse/keyboard. VGA Port The DB15-pn female connector s provded for montor. Serial Port The seral port s a 16550A hgh speed communcatons port that sends/ receves 16 bytes FIFOs. You can attach a seral mouse or other seral devces drectly to the connector. USB Port The USB (Unversal Seral Bus) port s for attachng USB devces such as keyboard, mouse, or other USB-compatble devces. LAN The standard RJ-45 LAN jack s for connecton to the Local Area Network (LAN). You can connect a network cable to t. LED Left Color Yellow LED State Off On (steady state) On (blnkng) Rght Green Off On Orange On Condton LAN lnk s not establshed. The computer s communcatng wth another computer on the LAN. 1000 Mbt/sec data rate s selected. Yellow Green/ Orange 2-9 Hardware Setup connector Serial ATA Connector: SATA_0 ~ SATA_5 Ths connector s a hgh-speed Seral ATA nterface port. Each connector can connect to one Seral ATA devce. Important Please do not fold the SATA cable into a 90-degree angle. Otherwise, data loss may occur during transmission. Fan Power Connector: CPUFAN0/1, SYSFAN1/2/3 The fan power connectors support system coolng fan wth +12V. [. . . ] Boot Device Priority The tems allow you to set the sequence of boot devces where BIOS attempts to load the dsk operatng system. Frst press <Enter> to enter the sub-menu. Then you may use the arrow keys ( ) to select the desired device, then press <+>, <-> or <PageUp>, <PageDown> key to move t up/down n the prorty lst. USB Drives Ths settng allows users to set the prorty of the USB devces. [. . . ]