User manual MTD 310355

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual MTD 310355. We hope that this MTD 310355 user guide will be useful to you.

Lastmanuals help download the user guide MTD 310355.


Mode d'emploi MTD 310355
Download
Manual abstract: user guide MTD 310355

Detailed instructions for use are in the User's Guide.

[. . . ] With proper operation and maintenance, it will provide you with years of service. In order to make the best use of your investment, be CERTAIN to familiarize yourself with the contents of the ENTIRE user manual before attempting to operate and maintain your unit. Be sure to carefully follow the step-by-step illustrations in this manual to start, operate and maintain your new product. In the manual there will be the following call-outs: NOTE:, WARNING / CAUTION and WARRANTY. [. . . ] CHAIN AND BAR LUBRICATION Always refill the chain oil tank each time the fuel tank is refilled. We recommend using McCulloch Chain, Bar and Sprocket Oil, which contains additives to reduce friction and wear and to assist in the prevention of pitch formation on the bar and chain. ENGINE PRE-START CHECKS E N Never start or operate the saw unless the bar and chain are properly installed. Fill the fuel tank (A) with correct fuel mixture (Figure 5-1A). Fill the oil tank (B) with correct chain and bar oil (Figure 5-1A). Be certain the CHAIN BRAKE® is disengaged (C) before starting unit (Figure 5-1A). Push the primer bulb (F) 10 times (Figure 5-2D). RECOMMENDED FUELS H Some conventional gasolines are being blended with oxygenates such as alcohol or an ether compound to B meet clean air standards. Your McCulloch engine is designed to operate satisfactorily on any gasoline intended for automotive use including oxygenated gasolines. CHAIN AND BAR LUBRICATION Always refill the chain oil tank each time the fuel tank is refilled. We recommend using McCulloch Chain, Bar and Sprocket Oil, which contains additives to reduce friction and wear and to assist in the prevention of pitch formation on the bar and chain. Place saw on a clear, firm, flat surface. Latch throttle advance: depress latch and hold (A) squeeze throttle trigger (B) release trigger and then the latch (Figure 5-2E). Hold saw firmly and pull starter rapidly 4 times. Depress and release trigger (E) for IDLE, then go to step 9 (Figure 5-2J). If engine failed to start, repeat these instructions. SAW CHAIN / BAR LUBRICATION Adequate lubrication of the saw chain is essential at all times to minimize friction with the guide bar. Running the saw with too little oil will decrease cutting efficiency, shorten saw chain life, cause rapid dulling of chain, and cause excessive wear of bar from overheating. Too little oil is evidenced by smoke, bar discoloration or pitch build-up. NOTE: Saw chain stretches during use, particularly when it is new, and it will occasionally be necessary to adjust and tighten it. New chain will require adjustment after about 5 minutes of operation. AUTOMATIC OILER Your chain saw is equipped with an automatic gear driven oiler system. [. . . ] CHAIN LUBRICATION: Always make sure the automatic oiler system is working properly. Keep the oil tank filled with McCulloch Chain, Bar and Sprocket Oil. Adequate lubrication of the bar and chain during cutting operations is essential to minimize friction with the guide bar. Never starve the bar and chain of lubricating oil. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MTD 310355

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual MTD 310355 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag