User manual MTD CC2025 41ADC25C712

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual MTD CC2025. We hope that this MTD CC2025 user guide will be useful to you.

Lastmanuals help download the user guide MTD CC2025.


Mode d'emploi MTD CC2025
Download

You may also download the following manuals related to this product:

   MTD CC2025 41ADC25C712 PARTS LIST (497 ko)
   MTD CC2025 41BDC25C010 PARTS LIST (401 ko)
   MTD CC2025 41ADC25C010 PARTS LIST (248 ko)

Manual abstract: user guide MTD CC202541ADC25C712

Detailed instructions for use are in the User's Guide.

[. . . ] Operator’s Manual 2-Cycle Trimmer Model CC 2025 IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY P/N 769-01385 (2/05) INTRODUCTION THANK YOU Thank you for buying this quality product. This modern outdoor power tool will provide many hours of useful service. You will find it to be a great labor-saving device. This operator’s manual provides you with easy-tounderstand operating instructions. [. . . ] 10) and securely tighten the knob before operating this unit. 90˚ Edge Trimming Hole To avoid serious personal injury and damage to the unit, shut the unit off before removing or installing add-ons. While firmly holding the upper shaft housing, pull the cutting attachment or add-on straight out of the EZ-Link™ coupler (Fig. Knob Installing the Cutting Attachment or Add-Ons NOTE: To make installing or removing the add-on easier, place the unit on the ground or on a work bench. 11 CAUTION: The add-ons with the coupler system is to be used in the primary hole only. Using the wrong hole could lead to personal injury or damage to the unit. For decorative trimming/edging with the line head cutting attachment, lock the release button of the cutting attachment into the 90° hole (Fig. 9 10 OPERATING INSTRUCTIONS HOLDING THE TRIMMER Always wear eye, hearing, foot and body protection to reduce the risk of injury when operating this unit. NOTE: Do not rest the Bump Head™ on the ground while the unit is running. Some line breakage will occur from: • Entanglement with foreign matter • Normal line fatigue • Attempting to cut thick, stalky weeds • Forcing the line into objects such as walls or fence posts or alter CAUTION: Do not remove blade the line cutting assembly. Excessive line length will make the clutch overheat. This may lead to serious personal injury or damage to the unit. WARNING: Before operating the unit, stand in the operating position (Fig. Check for the following: • The operator is wearing eye protection and proper clothing • With a slightly-bent right arm, the operator’s hand is holding the shaft grip • The operator’s left arm is straight, the left hand holding the D-handle • The unit is at waist level • The cutting attachment is parallel to the ground and easily contacts the grass without the need to bend over TIPS FOR BEST TRIMMING RESULTS • • Keep the cutting attachment parallel to the ground. Allow the tip of the line to do the cutting, especially along walls. Cutting with more than the tip will reduce cutting efficiency and may overload the engine. € Cut grass over 8 inches (200 mm) by working from top to bottom in small increments to avoid premature line wear or engine drag. € Cut from right to left whenever possible. Cutting to the left improves the unit's cutting efficiency. Clippings are thrown away from the operator. € Slowly move the trimmer into and out of the cutting area at the desired height. € Trim only when grass and weeds are dry. [. . . ] Any replacement part that is equivalent in performance or durability may be used in non-warranty maintenance or repair and will not reduce the warranty obligations of the manufacturer • The following components are included in the emission related warranty of the engine, air filter, carburetor, primer, fuel lines, fuel pick up/ fuel filter, ignition module, spark plug and muffler. 19 MANUFACTURER’S LIMITED WARRANTY FOR: The limited warranty set forth below is given by Cub Cadet LLC with respect to new merchandise purchased and used in the United States, its possessions and territories. Cub Cadet LLC warrants this product against defects in material and workmanship for a period of two (2) years commencing on the date of original purchase and will, at its option, repair or replace, free of charge, any part found to be defective in material or workmanship. This limited warranty shall only apply if this product has been operated and maintained in accordance with the Operator’s Manual furnished with the product, and has not been subject to misuse, abuse, commercial use, neglect, accident, improper maintenance, alteration, vandalism, theft, fire, water or damage because of other peril or natural disaster. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MTD CC2025

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual MTD CC2025 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag